Évaluations - 2, GPA: 3.5
(
)
)
|
Photos et spécifications Samsung PS-50P3HR |
Facilité d'utilisation
Installation Notes . Do not install the PDP on any place other than vertical walls. . To protect the performance of the PDP and prevent troubles, avoid the followings: - Do not install next to smoke and fire detectors. - Do not install in an area subjected to vibration or high voltage. - Do not install near or around any heating apparatus. . Use only recommended parts and components. PS42P3S/50P3H PS63P3H (depending on your model) 11 ENG Installing the Display on the Wall Attachment Panel 1 Remove the screws from the back of the PDP. 2 Use the screws and assemble the plastic hanger. . . Please ask the installers to install the wall mount bracket. . Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall mount bracket. . Please avoid catching your fingers while installing and adjusting the angle. . Please tightly secure the wall mount bracket to the wall to avoid injury from a falling PDP. 3 Tighten the screws of the plastic hanger to the back side of the PDP. 4 Put the 4 pegs on the PDP in the grooves of the wall mount bracket and pull down on the PDP (!) to secure it to the wall mount bracket (@). Tighten the screws as shown (#) so that the PDP cannot be separated from wall mount bracket. . The exterior of the PDP may be different than the picture. (Assembly and installation of the plastic hanger is the same.) PDP panel Wall attachment panel bracket Wall PS42P3S PS50P3H PS63P3H PS42P3S PS50P3H PS63P3H 12 ENG Connecting Speakers 1 Remove the screws on the rear of the PDP. 2 Hang the two “T” shaped hangers on the square holes on the rear of the PDP. 3 Tighten the PDP and the speaker bracket using the screws removed from the PDP. . When moving your PDP, do NOT hold the speaker connected to your PDP. It may damage the bracket clamping the speaker and your PDP together and result in a drop of your PDP and a risk of personal damage and injury. PS42P3S PS50P3H PS63P3H PS42P3S PS50P3H PS63P3H PS42P3S PS50P3H PS63P3H 13 ENG Connecting Speakers (continued) Ferrite Cores The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector. Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP. Sub-woofer speaker PS42P3S/PS50P3H Sub-woofer speaker PS63P3H . . The speakers MUST have to a power handling capability of 10 watts minimum (impedance 8.). . When you connect the speaker wire to the external speaker out connector, first bind the speaker wire round the ferrite core to secure it. Connecting to an Aerial or Cable Television Network ENG Rear of the PDP Cable Television Network or To view television channels correctly, a signal must be received by the set from one of the following sources: . An outdoor aerial . A cable television network . A satellite network 1 In the first three cases, connect the aerial or network input cable to the 75. coaxial socket on the rear of the PDP. 2 If you are using an indoor aerial, you may need to turn it when tuning your PDP until you obtain a picture that is both sharp and clear. For further details, refer to: . “Storing Channels Automatically” on page 20 . “Storing Channels Manually” on page 22 . When installing or re-installing your PDP, be sure to use the supplied coaxial antenna cable. If you connect using a different coaxial cable, there is risk of noise or interference to the screen image. (You must not use another general purpose cable. Use the 3M/5M/7M cable supplied by Samsung.) Connecting a Satellite Receiver or Decoder 14 Rear of the PDP Satellite receiver/ Decoder In order to watch television programmes broadcast via a satellite network, you must connect a satellite receiver to the rear of the PDP. Also, in order to descramble a coded transmission signal, you must connect a decoder to the rear of the PDP. Using a Coaxial cable Connect a coaxial cable to the: . Receiver (or Decoder) output socket. . Television aerial input socket. . If you wish to connect both a satellite receiver (or decoder) and a VCR, you should connect the: . Receiver (or Decoder) to the VCR . VCR to the PDP Otherwise, connect the receiver (or decoder) directly to the PDP. ” 1 Press the POWER ( ) button on the remote control. Result: The screen is turned off and the Standby indicator on the front of the PDP lights. Switching On and Off Placing in Standby Mode Front of the PDP TV TV 1 Press the POWER ( ) button on the remote control. Result: The screen is turned off and the Standby indicator on the front of the PDP lights. Switching On and Off Placing in Standby Mode Front of the PDP TV TV ENG To switch the PDP back on, simply press the POWER ( ) button again or a numeric button. . You can also switch on by pressing the P or button. 15 Becoming Familiar with the Remote Control ENG The remote control is used mainly to: . Change channels and a...
Ce manuel est également adapté pour les modèles :TV - PS-50P3H (6.75 mb)