Évaluations - 2, GPA: 4
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
¦ Install two 1.5 V AAA batteries. Do not mix old or used batteries with new ones. ¦ Close cover. ¦ To remove the batteries, perform the installation actions in reverse. PREPARATION LCD TV MODELS : 32/42/46/52/60LD5*** ACCESSORIES Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. PREPARATION ¦Image shown may differ from your TV. Owner’s Manual Ferrite Core (This item is not included for all models.)Power Cord Polishing Cloth Polishing cloth foruse on the screen. This item is not included for all models. * Lightly wipe anystains or fingerprintson the surface of the TV with the polishingcloth. Do not use exces- sive force. This may cause scratching ordiscolouration. x 8 M4 x 20 Batteries (AAA) Remote Control Protection Bolts for stand assembly 1-screw for stand fixing Cover (Only 32/42LD5***) Use of ferrite core (This feature is not available for all models.) Ferrite core can be used to reduce the electromagnetic wave when connecting the power cord. The closer the location of the ferrite core to the power plug, the better it is. Install the power plug closely. FRONT PANEL CONTROLS NOTE >TV can be placed in standby mode in order to reduce the power consumption. And TV should be switched off using the power switch on the TV if it will not be watched for some time, as this will reduce energy consumption. >The energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced, and this will reduce the overall running cost. PREPARATION CAUTION >Do not step on the glass stand or subject it to any impact. It may break, causing possible injury from fragments of glass, or the TV may fall. >Do not drag the TV. The floor or the product may be damaged. ¦ Image shown may differ from your TV. PROGRAMME VOLUME OK MENU INPUT POWER Power/Standby Indicator • Illuminates red in standby mode. • Illuminates blue when the TV is switched on. Intelligent SensorAdjusts picture according tothe surrounding conditions. Remote Control Sensor SPEAKER PREPARATION BACK PANEL INFORMATION ¦ Image shown may differ from your TV. PREPARATION Power Cord Socket This TV operates on an AC power. The volt- age is indicated on the Specifications page. (>p.137 to 147) Never attempt to operatethe TV on DC power. HDMI/DVI IN InputConnect an HDMI signal to HDMI IN. Or DVI(VIDEO) signal to HDMI/DVI port with DVI toHDMI cable. RGB IN InputConnect the output from a PC. OPTICAL DIGITAL AUDIO OUT Connect digital audio to various types ofequipment. Connect to a Digital Audio Component. Use an Optical audio cable. RGB/DVI Audio InputConnect the audio from a PC or DTV. Euro Scart Socket (AV1) Connect scart socket input or output from anexternal device to these jacks. Component InputConnect a component video/audio device tothese jacks. RS-232C IN (CONTROL & SERVICE) PORTConnect to the RS-232C port on a PC. This port is used for Service or Hotel mode. WIRELESS Control Connect the Wireless Media Box to the WIRELESS CONTROL jack on the TV. Antenna InputConnect antenna or cable to this jack. USB InputConnect USB storage device to this jack. PCMCIA (Personal Computer Memory Card International Association) Card SlotInsert the CI Module to PCMCIA CARD SLOT. (This feature is not available in all countries.) Headphone SocketPlug the headphone into the headphonesocket. Audio/Video InputConnect audio/video output from an externaldevice to these jacks. 1 2 3 4 8 9 10 11 12 1 2 3 64 5 7 98 11 2 12 13 14 10 5 6 7 13 14 STAND INSTALLATION ¦ Image shown may differ from your TV. When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. BACK COVER FOR WIRE ARRANGEMENT ¦ Image shown may differ from your TV. 1 Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section. PREPARATION 1 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. 2 Assemble the parts of the Stand Body with the Cover Base of the TV. Cover Base Stand Body Assemble the TV as shown. 34 Fix the 4 bolts securely using the holes in the back of the TV. 2 Open the Cable Management Clip as shown. Cable Management Clip Fit the Cable Management Clip as shown. 3 NOTE >Do not use the Cable Management Clip to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged. PREPARATION PREPARATION ATTACHING THE TV TO A DESK (Only 32/42LD5***) ¦ Image shown may differ from your TV. The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use onlyan attached screw. 1-Screw ( provided as parts of the product) Stand Desk WARNING >To prevent TV from falling over, the TV should be secur...
Ce manuel est également adapté pour les modèles :TV - 19LD351 (4.6 mb)
TV - 19LE3300 (4.6 mb)
TV - 32LD420 (4.6 mb)
TV - 32LD550 (4.6 mb)