Fabricant : LG
Taille : 8.45 mb
Nom Fichier :
|
Facilité d'utilisation
¦ This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 42/50PT2*** models. ¦ Image shown may differ from your TV. Signal Component HDMI 480i/576i O X 480p/576p O O 720p/1080i O O 1080p O (50/60Hz only) O (24Hz/30Hz/50Hz/60Hz) Component Input ports To achieve better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Y PB PR Video output ports on DVD player Y PB PR Y B-Y R-Y Y Cb Cr Y Pb Pr 1 Connect the video outputs (Y, PB, PR) of the external equipment (digital set-top box, DVD, etc.) to the COMPONENT IN VID EO jacks on the TV. Connect the audio outputs (Y, PB, PR) of the external equipment (digital set-top box, DVD, etc.) to the COMPONENT IN AUDI O jacks on the TV. 3 Turn on the external equipment. (Refer to the external equipment's manual for operating instructions.) 4 Select Component 1 input source using the INPUT button on the remote control. If connected to COMPONENT IN 2, select Component 2 input source. 2 3 external equipment setup /DVI IN RS-232C IN (CONTROL&SERVICE) ANTENNA IN COMPONENT IN AV IN 1 AUDIO VIDEO VIDEO 1 1 2 AUDIO IN (RGB/DVI) RGB IN (PC) /DVI IN RS-232C IN (CONTROL&SERVICE) ANTENNA IN COMPONENT IN AV IN 1 AUDIO VIDEO VIDEO 1 1 2 AUDIO IN (RGB/DVI) RGB IN (PC) /DVI IN RS-232C IN (CONTROL&SERVICE) ANTENNA IN COMPONENT IN AV IN 1 AUDIO VIDEO VIDEO 1 1 2 AUDIO IN (RGB/DVI) RGB IN (PC) DVI-PC OUTPUT AUDIO /DVI IN RS-232C IN (CONTROL&SERVICE) COMPONENT IN AV IN 1 AUDIO VIDEO R AUDIO L(MONO) VIDEO 1 1 2 VARIABLE AUDIO OUT AUDIO IN (RGB/DVI) RGB IN (PC) R S-VIDEO R OUTPUT SWITCH 1 Connect ing with a HDMI cable 2 ! ? NOTE >Check that your HDMI cable is High Speed HDMI Cable. If the HDMI cables are not High Speed HDMI Cable, flickering or no screen display can result. Please use the High Speed HDMI Cable. > HDMI mode supports PCM audio format only. > Audio format was reseted to Dolby/DTS/Bitstrem in DVD Player or STB, it should be changed to PCM. > We recommend using under 10m of the HDMI cable. When using over the length, connect an amplifier or repeater. > If the DVD does not support Auto HDMI, you must set the output resolution appropriately. 1 Connect the HDMI output of the external equipment (digital set-top box, DVD, etc.) to HDMI /DVI IN 1, HDMI IN 2 or HDMI IN 3 (Except for 42/50PT2***, 50PV2***) jack on the TV. 2 Turn on the external equipment. 3 Select HDMI 1, HDMI 2 or HDMI 3 (Except for 42/50PT2***, 50PV2***) input source using the INPUT button on the remote control. 4 exte rnal equipment set up external equipment setup AV IN2 COMPONENT IN VIDEO AUDIO VIDEO L(MONO) AUDIO R AV IN1 1 AUDIO IN (RGB/DVI) USB IN SERVICE ONLY RGB IN (PC) RS-232C IN (CONTROL) 26/32LD330 2 AUDIO IN (RGB/DVI) USB IN SERVICE ONLY RGB IN (PC) COMPONENT IN VIDEO Y PB PR L R AUDIO VIDEO /MONO AUDIO /DVI IN 1 2 RS-232C IN (CONTROL) OUTPUT ANT IN SWITCH ANT OUT S-VIDEO VIDEO L R /DVI IN 1 /DVI IN RS-232C IN (CONTROL&SERVICE) ANTENNA IN COMPONENT IN AV IN 1 AUDIO VIDEO VIDEO 1 1 2 AUDIO IN (RGB/DVI) RGB IN (PC) DVI-PC OUTPUT AUDIO 1 2 Usb set up Connect the USB device to the USB IN jack on the TV. 2 After connecting the USB IN jack, you use the USB function. (. p.31) 1 Connect ing with a HDMI to DVI cable or 1 Connect the digital set-top box or the DVI output of the PC to HDMI /DVI IN 1 jack on the TV. 2 Connect the audio output of the digital set-top box or the PC audio output to the AUDI O IN (RG B/DVI) jack on the TV. 3 Turn on the digital set-top box or the PC and the TV. (Refer to the digital set-top box or the PC manual for operating instructions.) 4 Select HDMI 1 input source using the INPUT button on the remote control. 5 external equipment setup ANTENNA IN COMPONENT IN AV IN 1 AUDIO VIDEO VIDEO 1 2 IN DVI) DVI-PC OUTPUT AUDIO /DVI IN RS-232C IN (CONTROL&SERVICE) ANTENNA IN COMPONENT IN AV IN 1 AUDIO VIDEO R AUDIO L(MONO) VIDEO 1 1 2 VARIABLE AUDIO OUT AUDIO IN (RGB/DVI) RGB IN (PC) R L VIDEO S-VIDEO R L VIDEO OUTPUT SWITCH ANT IN ANT OUT Connect ing with a RCA cable >>If you have a mono VCR, connect the audio cable from the VCR to the AUDI O L/MONO jack of the TV. ! ? NOTE Camcorder Video Game Set or 1 Connect the AUDI O/VID EO jacks between TV and VCR or external equipment. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red) 2 Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Or, Operate the corresponding external equipment. (Refer to external equipment operating guide.) 3 Select AV1 input source using the INPUT button on the remote control. If connected to AV IN2, select AV2 input source. 1 6 exte rnal equipment set up external equipment setup Exte rnal ste reo set up Use to connected either an external amplifier, or add a subwoofer to your surround sound system. AV IN2 IN 2 ANTENNA IN COMPONENT IN 2 ANTENNA IN COMPONENT IN AUDIO VIDEO 1 2 R L VIDEO S-VIDEO R L VIDEO OUTPUT SWITCH ANT IN ANT OUT /DVI IN RS-232C IN (CONTROL&SERVICE) ANTENNA IN COMPONENT I...
Ce manuel est également adapté pour les modèles :TV - 42PT350R (8.45 mb)