Évaluations - , GPA: ( )

Instructions Toshiba, Modèle 26AV500U

Fabricant : Toshiba
Taille : 5.25 mb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

To select the menu language: 1 Press and open the Setup menu. 2 Highlight Menu Language. 3 Press • or to select your preferred menu language. 4 Press to close the Setup menu. Configuring the antenna input source for the ANT/CABLE terminal To configure the ANT input source: 1 Press and open the Setup menu. 2 Highlight Input Configuration. 3 Press • or to select the input source (Cable or Antenna) which input signal connecting to ANT/ CABLE terminal on the TV. Viewing the digital signal meter You can view the digital signal meter in the ANT digital TV input source only. To view the digital signal meter: 1 Press and open the Setup menu. 2 Highlight DTV Signal Meter. 3 Press • or , a new set of DTV Signal Meter menu icons will appear as shown below. Viewing the system status To view the system status: 1 Press and open the Setup menu. 2 Highlight System Status. 3 Press • or , the System Information menu will appear as below. 9 Chapter 5: Setting up your TV Programming channels into the TV’s channel memory When you press or on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory. Follow the steps below to program channels into the TV’s channel memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory. Note: • You must configure the antenna input source before programming channels (. page 29). • The automatic channel programming process erases channels that were previously programmed into the TV’s memory. • To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. • Programming channels when the antenna input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. To program channels automatically: 1 Configure the antenna input source, if you have not already done so (. page 29). 2 Press and open the Setup menu. 3 Highlight Auto Ch Search. 4 Press • or to begin channel programming (A new set of Auto Ch Search menu icons will appear as shown below.) The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Progress(%)” appears a white bar to indicate the scanning status (as shown above). 5 To cancel channel programming, press on the remote control. When channel programming is finished, press or to view the programmed channels. Manually adding channels in the channel memory Auto Ch Search can search and save channel information into the channel memory. There are two ways to add channel information into the channel memory if the program are not exist in Channel memory previously: (1)To add On Ch Search: 1 Press and open the Setup menu. 2 Highlight Add On Ch Search. 3 Press • or to begin channel programming (A new set of Add On Ch Search menu icons will appear as below.) (2)Manually to add channel on a physical channel For analog Channel: 1 Use the Channel Numbers to enter the channel number that you want to add directly. (digital CH may use the Dash on the remote control, for example,56-1 ) 2 Press or on the remote control to save this adding channel to Channel memory. 0 Chapter 5: Setting up your TV Manually deleting channels in the channel memory There is no method really to delete the channel memory except executing Auto Ch Search with a empty RF input. But there is a simple way to disable undesired Channel. 1 Press and open the Setup menu 2 Highlight Manual Ch Set. 3. Pressuor,anewsetofManual Channel Set Menu willappearasbelow. Press p• buttons to highlight the channel. Press to cycle select Channel is Viewable or Not Viewable. 4 5 * If the Channel is marked to "Not Viewable". The channel will be skip when you press " " or " ", unless you set it to "Viewable" or press Channel Number directly. Channel memory checking table All the channel search result can be seen on the Manual Ch Set. 1 Press 2 Highlight Manual Ch Set. and adding or deleting and open the Setup menu channel memory. Please refer above description. Channel Labels Menu A list of common channel labels (logos) for various channels (ABC, CBS, etc.) will be programmed into the TV. You will be able to view and assign these logos from the Channel Labels window. If the desired channel label is not provided in the list, you will be able to manually enter/edit labels using the arrow buttons. 1 Press and open the Setup menu 2 Highlight Channel Labels. 3 Press • or , Channel Labels Menu will appear as below. 4 Left block is original channel No, right block is new channel labe...