Évaluations - 3, GPA: 3.7 ( )

Fabricant : Toshiba Taille : 3.91 mb Nom Fichier : Langue d'enseignement:

Home CH Setup Favorite Channels Closed Caption Mode Off Closed Caption Advanced Input Labeling Menu Language English Preferences English Francais Espanol Navigate Select Back ExitCH RTN EXIT 4. Press EXIT to close the Preferences menu. Configuring the antenna input sources To configure the ANT 1 and ANT 2 input sources: 1. Press MENU and open the Setup menu. 2. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen, as shown in step 3 below.) Navigate Select Back ExitCH RTN EXIT Installation Sleep Timer On/Off Timer HDMI 1 Audio Auto Auto 2 Sec 15 min HDMI 2 Audio Slide Show Interval AVHD Skip Time Setup 3. Open the Terrestrial menu, highlight Input Configuration, and press ENTER. Note: The Terrestrial menu may not be accessible (items will be “grayed out”) in some instances (for example, if a cable box is connected to the ANT 1 input or if one of the VIDEO modes is the current input during TV Guide On Screen™ setup). Terrestrial Input Configuration Channel Program Channel Add/Delete Signal Meter Navigate Select Back ExitCH RTN EXIT 4. Press x or • to select the input source (Cable or Antenna) for the ANT 1 input on the TV. Note: If a cable box is connected to the ANT 1 input during TV Guide On Screen™ setup, the entire Terrestrial menu will not be accessible, including the input source for ANT 1, which will automatically display “Cable Box.” 5. Press z and then x or • to select the input source (Cable or antenna) for the ANT 2 input on the TV, if applicable. If you have not connected anything to ANT 2, skip this step. Input Configuration Antenna 1 In Antenna 2 In Cable Antenna Cancel Done 6. To save your new settings, highlight Done and press ENTER. To revert to your original settings, highlight Cancel and press ENTER. Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. Chapter 6: Setting up your TV Chapter 6: Setting up your TV Programming channels into the TV’s channel memory When you press CHANNEL y or z on the remote control or TV control panel, your TV will stop only on the channels stored in the TV’s channel memory. Follow the steps below to program channels into the TV’s channel memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels. Note: •You must configure the antenna input sources before programming channels (see page 41). • If the input signal type is set to CABLE for an antenna input, the automatic channel programming process erases channels that were previously programmed into the TV’s memory. • If the input signal type is set to ANTENNA, the automatic channel programming process does NOT erase channels that were previously programmed into the TV’s memory, but adds newly found channels to the existing set of programmed channels. To remove a channel from the memory, you must manually delete it (see next page). •To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. • Programming channels for an antenna input configured for CABLE will take substantially longer than for an antenna input configured for ANTENNA. This is normal; however, once channel programming is completed, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. • If you have a CableCARD™ inserted (page 12), channel programming for ANT 1 is disabled because the CableCARD™ automatically loads the Cable channel list into the TV’s channel memory. To program channels automatically: 1. Make sure you have configured the antenna input sources. See page 41 for details. 2. Press MENU and open the Setup menu. 3. Highlight Installation and press ENTER. (A new set of Installation menu icons will appear on-screen). Navigate Select Back ExitCH RTN EXIT Installation Sleep Timer On/Off Timer HDMI 1 Audio Auto Auto 2 Sec 15 min HDMI 2 Audio Slide Show Interval AVHD Skip Time Setup 4. Open the Terrestrial menu, highlight Channel Program, and press ENTER. 5. Highlight ANT 1 or ANT 2, depending on which antenna input you want to program channels for, and then press ENTER to start automatic channel programming. Terrestrial Input Configuration Channel Program Channel Add/Delete Signal Meter Navigate Select Back ExitCH RTN EXIT ANT 1 Antenna Scanning channels, please wait ... Abort 52% The TV will automatically cycle through all the channels for the antenna input you selected, and store all active channels in the channel memory. While the TV is cycling through the channels, the message “Scanning channels, please wait” appears (as shown above). 6. To cancel channel programming, either press EXIT or highlight Abort in the on-screen display and press ENTER. When channel programming is done, press CHANNEL y or z to view the programmed channels. Channel Numbers TV control panel CHANNEL yz CHA...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :