Évaluations - 3, GPA: 4 ( )

Fabricant : Toshiba Taille : 3.67 mb Nom Fichier : Langue d'enseignement:

The AUDIO1/2 (Receiver, CD) modes will have their own volume even if Volume Lock is on TV, CABLE/SAT, VCR, or DVD. See “Using the Volume Lock feature” on page 17. Index AppendixUsing the TV’s Setting upUsing theConnectingIntroductionFeatures your TV Remote Control your TV 15 Index AppendixUsing the TV’s Setting upUsing theConnectingIntroductionFeatures your TV Remote Control your TV Programming the remote control for use with your audio/video devices Device code setup 1. Refer to the Device code table on pages 18-21 to find the number that corresponds to the brand name of your device. If more than one number is listed, try each one separately until you find the one that works. 2. Press MODE until the Mode indicator of the device (CABLE/ SAT, VCR, DVD, AUDIO1, AUDIO2) lights up. 3. Hold down the RECALL button while using the Number buttons to enter the four-digit code number of your brand of device. If a valid code has been entered, the mode indicator will blink twice. If an invalid code is entered, there will be one long blink. 4. Point the remote control at the device and press POWER to test the code number. If the device turns on, you have entered the right number. If the device does not respond to the remote control, you may have entered the wrong number. Repeat steps 3 and 4 using another code number. 5. Press MODE to select the TV mode to control the TV. Searching and sampling the code of a device (991) If you do not know the device code for a particular target unit, you can cycle the remote through the available codes for that device mode and sample functions in order to find the code that properly operates the desired target device. The keys available to be sampled, provided they are applicable to that mode, are 0, 1, 2, 3, POWER, VOL y, CH y, PLAY and STOP. Invalid keys will be ignored while in program mode. To cycle through each available device code and sample its functions: 1. Press MODE to select the mode you want to set up. 2. While holding down the RECALL button, press 9–9–1. The remote control will enter program mode. 3. Point the remote at the target device and press POWER (or other function buttons that are available to be sampled). 4. If the device responds to the remote: Press RECALL to store the device code. The mode indicator will blink twice and the remote will exit the program mode. If the device does not respond to the remote: Press Menu y then press POWER. Repeat this step until the device responds to the remote, then press RECALL. Note: If a search cycle has been completed, the mode indicator will blink three times. The remote will begin to cycle through the available codes again. If no key is pressed within ten seconds while programming, the remote will exit the program mode and return to the previous code. Note: • Each time you replace the batteries, you must reprogram the remote control. • Some newer VCRs are capable of working on either of two remote codes. These VCRs have a switch labeled “VCR1/VCR2.” If your VCR has this kind of switch, it may not respond to any of the code numbers for POWER Number MODE Menu y RECALL your VCR brand name. In this case, set the switch to the other position (VCR1 or VCR2) and reprogram the remote control. 16 Verifying the device code (990) Use this feature to verify the codes for your other devices. The number of blinks after pressing the 1, 2, 3, and 4 buttons is the 4-digit code set up for that mode. Example: To verify the VCR code is 2345: Number 1. Press MODE to select the VCR mode. MODE 2. While holding down the RECALL button, press 9–9–0. 3. Press 1 . 2 blinks. 4. Press 2 . 3 blinks. 5. Press 3 . 4 blinks. 6. Press 4 . 5 blinks. You can verify that the device code of the VCR mode is “2345.” VOL y z RECALL Using the Volume Lock feature (993) For the TV, CABLE/SAT, VCR, and DVD modes, the volume controls (VOL yz and MUTE) can be programmed or locked to the selected device mode. This feature does not apply to the AUDIO1/2 modes. Example: To lock the volume controls to always jump to the CABLE/ SAT mode: 1. Press MODE to select the CABLE/SAT mode. 2. While holding down the RECALL button, press 9–9–3. 3. Press VOL y. The Mode indicator will blink two times (locked). The following table describes in more detail the Volume Lock implementation. Volume Locked to TV CBL/SAT VCR DVD AUD1 AUD2 TV (default) TV TV TV TV AUD1 AUD2 CBL/SAT CBL/SAT CBL/SAT CBL/SAT CBL/SAT AUD1 AUD2 VCR VCR VCR VCR VCR AUD1 AUD2 DVD DVD DVD DVD DVD AUD1 AUD2 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD1 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2 AUD2 To reset the volume controls to the original device code: 1. While holding down the RECALL button, press 9–9–3. 2. Press VOL z. The Mode indicator will blink four times (unlocked). Operational feature Reset (980) This feature clears all setup features not related to “Device code set up” and resets the Volume Lock to “TV.” To reset the features: While holding down the RECALL button, press 9–8–0. The Mode indicator will blink two times, then pause and b...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :