Évaluations - 0, GPA: 0 ( )

Fabricant : Philips Taille : 2.15 mb Nom Fichier : Langue d'enseignement:

The source list is displayed. 4. Press the i key to select EXT4 and Connecting With an HDMI Connector press the . / key to confirm your As shown in the figure below, connect your equipment with the HDMI connec1. selection. Bottom of TV tor. Press the2. key on the remote control. The source list is displayed. Press the i key to select HDMI1 or3. HDMI2 and press the . / key to confirm your selection. 1 2 Connect a DVD player, satellite receiver or cable box 5. As shown in the following figure, if you are using a cable box and/or a satellite receiver, also connect the cable TV cable and/or the satellite aerial cable (3) to the aerial cable (4). Connecting With Component Video Connectors Bottom of TV As shown in the following figure, connect the three separate component video cables (1) to the YPbPr jacks on the DVD player and to the Y (yellow), Pb (blue) and Pr (red) jacks of EXT4 on the TV. 1. Connect the audio cable to the DVD’s audio L and R jacks and to the L/R AUDIO jack of EXT4 (2). 2. 1 2 3 4 Cable EN-28 Cable colours Cables are often colour coded. Connect like colour with like colour. For example, connect red to red. The labels for the component video sockets can differ depending on the DVD player connected. Although the abbreviations may vary, the letters B and R stand for the blue and red component signals, respectively. The letter Y indicates the luminance signal. Refer to the user manual of your DVD player for definitions and information about connections. For optimal viewing, switch your equipment to the highest supported display mode. Warning: If you notice problems such as scrolling images, wrong colours, no colour or no picture, verify that your TV is connected correctly. Verify also that the resolution and the signal standard of the peripheral equipment is correct. For information about the resolution and the signal standard of the peripheral equipment, see the user manual for the equipment. Connecting a PC Note: The digital output of the PC can be connected via DVI to HDMI cable. Connection by VGA is not supported. Before you connect your PC to the TV, configure your PC with a monitor refresh frequency of 60 Hz. Connecting a PC with a DVI connector 1. As shown in the following figure, connect your PC to the TV with a DVI to HDMI cable (1). 2. Connect the audio cable to the audio jack on the PC and to the L/R AUDIO jack on the EXT3 of the TV (2). 3. Press the key on the remote control. The source list is displayed. 4. Press the i key to select HDMI1 or HDMI2 and press the . / key to confirm your selection. Side of TV Rear of TV 12 Supported PC resolutions 640 x 480, 60 Hz 800 x 600, 75 Hz 640 x 480, 72 Hz 800 x 600, 85 Hz 640 x 480, 75 Hz 1024 x 768, 60 Hz 640 x 480, 85 Hz 1024 x 768, 70 Hz 800 x 600, 60 Hz 1024 x 768, 75 Hz 800 x 600, 72 Hz 1024 x 768, 85 Hz For LCD TVs only 1280 x 768, 60 Hz 1280 x 1024, 60 Hz 1360 x 768, 60 Hz EN EN-29 Connecting a camera, camcorder or game console 1. As shown in the figure below, connect your camera, camcorder or game console in at the side of the TV. 2. Press the key on the remote control. The source list is displayed. 3. Press the i key to select EXT3 and press the . / key to confirm your selection. •For mono equipment, connect to VIDEO (2) and AUDIO L (3) •For stereo equipment, connect both AUDIO L and AUDIO R (3) •To obtain S-VHS quality with an S-VHS camcorder connect the S-VHS cables with the S-VIDEO input (1) and AUDIO L / R inputs (3) Warning: Do not connect cables (1) and (2) at the same time. Connecting both cables (1) and (2) can cause picture distortion. Side of TV 3 2 1 Connect headphones 1. As shown in the figure below, insert the headphones plug into the headphone socket at the side of the TV. 2. Press the key on the remote control. The source list is displayed. 3. Press the i key to select EXT3 and press the . / key to confirm your selection. The headphone socket has a 3.5 mm jack. The headphone impedance must be between 8 and 4000 Ohm. TIP: Press the key on the remote control to switch off the sound from loudspeakers of the TV. To switch on the sound, press the key again. EN-30 20 Troubleshooting The following table describes some common problems you can encounter when using your TV. Consider the proposed solutions before you call for service. Symptom Possible solutions No display on Verify that the power cord is properly connected into the mains• screen socket and into the TV. If the power cord is correctly inserted but there is no power, perform the following steps: Disconnect power cord or wall plug Wait for 60 seconds and then re-insert plug Switch on the TV Press the key on the remote control • • • • • Poor reception Verify that the aerial is connected to the TV and to the wall aerial• (snow) socket. Manually tune your picture as described in Manual Store on page 10. Verify that you have chosen the right TV system. For information about TV systems, see Manual Store on page 10. Check the signal strength by pressing the key • • • No pic...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :