Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
TV - LW20M11C (5.89 mb)
TV - LW20M11C (293.26 kb)
Facilité d'utilisation
Please do not tilt the television beyond the specified range. Using excessive force to tilt the television beyond the specified range may cause permanent damage to the mechanical part of the stand. English-8 ENG-00-13.qxd 10/1/03 10:09 AM Page 9 Viewing Pictures From External Sources Once you have connected up your various audio and video systems, you can view the different sources by selecting the appropriate input. Inserting the Batteries in the Remote Control You must insert or replace the batteries in the remote control when you: Purchase your set Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it. 2 Install two AAA size batteries. + on the battery against + on the remote control -on the battery against -on the remote control 3 Replace the cover by aligning it with the base of the remote control and pressing it back into place. Do not mix battery types, i.e. alkaline and manganese. English-9 ENG-00-13.qxd 10/1/03 10:09 AM Page 10 Viewing the Remote Control (All Functions Except Teletext) Television On/Off Numeric buttons for direct channel access One/Two-digit channel selection Volume up or down Temporary sound switch-off Automatic switch-off Menu display and change confirmation Sound mode selection Previous channel Next channel Previous channel Available source selection Use to see information on the current broadcast Exit the OSD Control the cursor in the menu Picture size selection Picture freeze Picture effect selection Sound effect selection The performance of the remote control may be affected by bright light. English-10 ENG-00-13.qxd 10/1/03 10:09 AM Page 11 Viewing the Remote Control (Teletext Functions) Teletext hold Teletext store Teletext Index Teletext display/ mix both teletext information and the normal broadcast Teletext sub-page P :Teletext next page P :Teletext previous page Teletext mode selection (LIST/FLOF) Teletext reveal Teletext cancel Teletext size selection English-11 ENG-00-13.qxd 10/1/03 10:09 AM Page 12 hing On and Off The mains lead is attached to the rear of your set. If you purchased this set in the United Kingdom, refer to page 46 for further instructions on plug wiring. 1 Plug the mains lead into an appropriate socket. Result: When the power cord is plugged in, the LED turns red. 2 Press the POWER button to switch on. 3 To switch off, press the POWER button again. Placing in Standby Mode our set can be placed in Standby mode in order to reduce the power consumption. The Standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example). 1 Press the POWER button. 2 To switch back on, simply press the POWER button again or a numeric button. Do not leave your set in Standby mode for long periods of time (when you are away on holiday, for example). Turn off by pressing the POWER button. It is best to unplug the set from the mains and aerial. English-12 ENG-00-13.qxd 10/1/03 11:49 AM Page 13 Becoming Familiar with the Remote Control The remote control is used mainly to: Change channels and adjust the volume Set up your set using the on-screen menu system The following table presents the most frequently used buttons and their functions. Button Viewing Function Menu Function Used to display the next - stored channel. Used to display the - previous stored channel. PRE-CH Used to switch repeatedly between the last two channels displayed. (PRE-CH; Previous Channel) - Used to display the corresponding channels. -/--Used to select a channel numbered ten or over. Press this button, and the “--” symbol is displayed. Enter the two-digit channel number. Used to increase the - volume. Used to decrease the - volume. MUTE Used to switch the sound off temporarily. To turn the sound back on, press this button again, or press the + or -button. MENU Used to display the Used to return to the previous on-screen menu system. menu or normal viewing. EXIT Used to exit the menu system and return directly to normal viewing. Display a submenu containing selections for the current menu option. Search backwards/forwards manually for channels Increase/decrease a menu option value English-13 ENG-14-29.qxd 10/1/03 10:10 AM Page 14 Plug & Play When the set is initially powered ON, you are automatically presented with a series of basic customer settings. The following settings are available. 1 If the set is in standby mode, press the POWER button on the remote control. Result: The message Plug & Play is displayed. It appears for a little while, and then the Language menu is automatically displayed. 2 Select the appropriate Language by pressing the or button. The available languages are listed. You can choose one of 18 Languages. 3 Press the ENTER button to confirm your choice. Result: The message Ant. Input Check is displayed with OK selected. 4 Press the ENTER button. 5 Select your Country by pressing the or button. Press the ENTER button...