Évaluations - 5, GPA: 4.2
(
)
)
|
Facilité d'utilisation
– If you do not have a VCR, connect signal directly to TV 75 ohm jack. CA TV FRANCHISE NOTE: Cable companies, like public utilities, are fran- chised by local government authorities. T o receive cable programs, even with equip- ment which is capable of receiving cable channels, the consumer must sub- scribe to the cable company’ s ser vice. INFROM ANT. OUTOUT TO TVCATV INOUT TO TVS-VIDEOCH3CH4VIDEOL-AUDIO-RVIDEOL-AUDIO-RIN FROM SAT. INOUTAUDIO VIDEO INPUTCOMPPrPbYAV2S-VIDEOVIDEO(MONO) UHF/VHF/CATV75.AUDIOOUTPUTRLTV Back VCR Back Connection: is necessary: Notes: – If you do not have a cable box, connect cable directly to TV 75 ohm jack or VCR. – If you do not have a VCR, connect signal directly to TV 75 ohm jack. S CONNECTING CABLE SERVICE, OR RF ANTENNA, OR SATELLITE DISH The TV will automatically select the correct Antenna mode Exception—When the Video mode is selected, the TV will for the type of RF signal you connect. not automatically switch off when signal reception has stopped for 15 minutes. TV will switch off automatically after 15 minutes if there is no signal reception (cable out or station not broadcasting). If you move the TV to a new location, press the RESET key twice after connecting the signal and turning on the TV. INITIAL SET-UP 1. Install batteries in remote control, see page 9. 2. Connect signal, see below. 3. Plug in AC power cord. RECEIVER TO TV Cable Box Satellite Receiver 4. Press POWER key to turn on TV. 5. Follow on-screen instructions, see pages 11 ~ 12. RF Antenna Operational Tip for No Signal If the TV is used as a monitor only, with a DVD player or some other type of external equipment, and no cable or antenna signal available, the following setup is – Your TV is designed to automatically search for available channels. Therefore, the initial start up requires that you press the MENU key, enabling the TV to automatically go through the channel search process before you can operate the TV. After the initial channel search is completed, you must press the MENU key again to complete the channel search process. This may take several minutes. – After the channel search process is complete (2 searches), you can press the INPUT key on the remote control to use the TV as a monitor. Need help?Visit our Web site at or Call 1-800-877-5032 FRONT AND BACK PANELS FRONT Model DS27425 MENUL - AUDIO - RVIDEO INCHVOLPOWER Audio/Video In Jacks (AV1) Connect video equipment here (see page 7). BACK 480i Component Video In Jacks (Component 2, Y, Pb, Pr) Connect video equipment here (see page 6). Note: Audio/Video Input (AV2) and Component inputs share the same audio (R/L) input jacks. Audio/Video In Jacks (AV2) Connect video equipment here (see pages 6 and 8). Note: S-Video connection will override an AV2 video connection. POSITIONING THE TV Do not position the TV in a confined area. Allow space for normal air circulation around electronic parts. AUDIO VIDEO INPUTCOMPPrPbYAV2S-VIDEOVIDEO(MONO) UHF/VHF/CATV75.AUDIOOUTPUTRL Audio Out Jacks Connect external audio equipment here (see page 7). S-Video In Terminal To enhance video detail use the AV2 S-Video jack instead of the AV2 Video jack, if available on your external equipment. (An S-Video connection will override connection to the AV2 video input jack. See page 8.) Need help?Visit our Web site at or Call 1-800-877-5032 USING THE COMPONENT VIDEO AND AUDIO INPUT JACKS CONNECTING A DVD PLAYER Switch off TV and external equipment before connecting cables. (Cables are not supplied.) Connect a DVD Player or other equipment’s interlaced Component Video Out to the TV Component Video In (Y-Pb-Pr) Jacks. Connect the DVD Player’s Audio Out to the TV A/V2 Audio In (L/R) Jacks. Press POWER to turn on the TV. Turn on external equipment also. To access Audio/Video inputs, press the INPUT key to Notes: DVD Player component output must be set to Interlaced (480i). Audio/Video Input (AV2) and Component inputs share the same audio (R/L) input jacks. Connect equipment to the Component2 video input or the AV2 video input, but not both types at the same time. select COMPONENT2. DVD Player TV BACK What you will need for connections: Component video cable – 1 Audio Cable – 1 123RESETINPUTPOWER123 Remote Control A solid Blue screen with COMPONENT2 displayed Press INPUT key after connecting cables to access means that the Video mode is selected, but no signal the A/V inputs.There is NO need to tune to a blank is being detected at the Component jacks. Check con- channel. nection, and turn on external equipment. Need help?Visit our Web site at or Call 1-800-877-5032 MENUL - AUDIO - RVIDEO INCHVOLPOWERL - AUDIO - RVIDEO IN MENUL - AUDIO - RVIDEO INCHVOLPOWERL - AUDIO - RVIDEO INS CONNECTING AUDIO OUT JACKS TO A STEREO AMPLIFIER Switch off TV and external equipment before connecting cables. (Cables are not supplied.) Connect the TV Audio Out (R/L) to the Stereo Amplifier In (R/L). Press POWER to turn on the TV. T...