Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
In these cases, change the angle of the lighting or the TV screen, or operate the remote control closer to the IR sensor. 2Insert the two supplied AAA batteries into the battery compartment. Make sure that the (+) and (-) symbols on the batteries match the diagram inside the compartment. - + + - Insignia NS-20CLTV 20" Combo DVD/LCD TV Connecting to video sources Connecting to a standardvideo source Your TV supports multiple video source inputs. Connecting to an antennaor cable/satellite For temporary or easy-access video receiver connections, use the side jacks (AV2). For more permanent connections, use the rear jacks (AV1). INPUT RF INPUT VGA OUTPUT AUDIO VGA INPUT 2 1 3 To connect an external antenna or cable/ satellite receiver: 1 Remove the port cover on the back of the TV (1). 2 Connect the antenna terminal from an antenna or cable/satellite receiver (3) to the antenna input jack on the TV (2). 3 Press the INPUT button and the buttons to set the TV’s signal input to TV. 1 R CB / PB Y AUDIO L R CR / PR INPUT 3 S-VIDEO AUDIO VIDEO L INPUT 1 VIDEO L R AUDIO INPUT 2 2 3 4 5 6 7 8 To connect a standard video source to AV1 jacks: 1 Connect an RCA video cable (2) to a standard video source (1) and the back VIDEO jack (5). 2 Connect RCA audio cables (4) to the source’s audio output jacks and the upper AUDIO L and R jacks on the back panel (5). 3 Press the INPUT button and the buttons to set the TV’s signal input to AV1. To connect a standard video source to AV2 jacks: 1 Connect an RCA video cable (6) to a standard video source (1) and the side VIDEO jack (8). 2 Connect RCA audio cables (7) to the source’s audio output jacks and the side AUDIO L and R jacks (8). 3 Press the INPUT button and the buttons to set the TV’s signal input to AV2. Insignia NS-20CLTV 20" Combo DVD/LCD TV To connect a standard S-Video source to Connecting to a computer AV1 jacks: 1 Connect an S-Video cable (3) to a standard video source (1) and the back S-VIDEO jack (5). 2 Connect RCA audio cables (4) to the source’s audio output jacks and the back AUDIO L and R jacks (5). 3 Press the INPUT button and the buttons to set the TV’s signal input to S-Video. Connecting to a component video source INPUT RF INPUT VGA OUTPUT AUDIO VGA INPUT 1 R B / PB Y AUDIO L R INPUT 3 S-VIDEO AUDIO VIDEO L INPUT 1 4 3 1 2 2 3 4 To connect a computer video source to the VGA jacks: 1 Remove the port cover on the back of the TV (1). 2 Connect a VGA cable (2) from the computer (4) to the VGA INPUT port on the TV. 3 Connect a male-to-male audio cable (3) from the computer (4) to the AUDIO VGA INPUT port on the TV. 4 Press the INPUT button and the buttons to set the TV’s signal input to PC. Note The best resolution for displaying computer video on this TV is 1280 . 768. To connect a progressive-scan or HDTV video source to Y/Pb/Pr jacks: 1 Connect component video cables (2) to a progressive-scan or HDTV video source (1) and the back Y/Pb/Pr jacks (3). 2 Connect RCA audio cables (4) to the source’s audio output jacks and the lower AUDIO L and R jacks on the back panel (3). 3 Press the INPUT button and the buttons to set the TV’s signal input to YPbPr. Using your TV Turning the power on and off To turn the power on and off: 1 Press the POWER button on the side panel of the TV or on the remote control. The POWER/STANDBY indicator turns green. 2 To turn off the TV, press the POWER button again. The screen image disappears and the POWER/STANDBY indicator turns red. Note A small amount of electric power is consumed even when the power is turned off. Insignia NS-20CLTV 20" Combo DVD/LCD TV Changing the volume You can change the volume using the TV’s side panel or the remote control. To change the volume: 1 Press VOL+ or VOL-. 2 Press MUTE to mute the sound, and press it again to restore sound. Changing the video source Your TV supports multiple video sources. To select the video source: • Press the INPUT button to select from the following signal modes, then press ENTER to confirm the selection: •TV •AV1 •AV2 •S-Video •DVD •YPbPr • PC Changing channels To change channels: • Press CH+/- or CH / . To enter a channel number directly: • Press the number buttons on the remote control. To switch between two channels: 1 Press RECALL to change from the currently tuned channel to the previous channel. 2 Press RECALL again to change back to the originally tuned channel. Programming channels into memory To automatically program channels into memory: 1 Press TV MENU on the remote control, then press to highlight the INSTALL icon. The INSTALL menu opens. TV mode LANGUAGE TUNER MODE AUTO PROGRAM CHANNEL EDIT FACTORY RESET MOVE SELECT RETURN ENGLISH EXITENTER ANTENNA INSTALL Other modes LANGUAGE FACTORY RESET MOVE SELECT RETURN ENGLISH EXITENTER INSTALL 2 Press to enter the INSTALL menu. 3 Press to select AUTO PROGRAM, then press to start the auto search. The TV searches and memorizes all channels available in ...