Log:
Évaluations - 4, GPA: 3.5 ( )

Instructions Vidikron, Modèle Vision 100t

Fabricant : Vidikron
Taille : 4.17 mb
Nom Fichier : db9746fe-ee3e-4730-8214-14dc75420347.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Caution The input voltage to the AutoScope lens motor must be between 100 and 120 VAC. Do not connect the AutoScope lens motor to a 200-240 VAC power source! 4Operation 4.1 Turning on the Power 1.Turn on your source components. 2.Turn on the main power switch on the projector. 3.If this is an AutoScope-equipped projector, turn on the main power switch at the rear of the AutoScope lens motor. The lens motor power switch is located next to the AC input. 4.Press the ON button on the remote control – or the POWER button on the Vision 90t/100t rear panel – to turn on the projector. The vacuum fluorescent display on the Vision 90t/100t rear panel briefly displays “Starting Display.” 5.When the projector is ready for use, the fluorescent display indicates the active source, signal format (NTSC or PAL), input resolution and aspect ratio; for example: Component SD NTSC 480iAnamorphic Vidikron 90Current SourceFormatInputResolutionAspectRatio 4.2 Adjusting the Picture Orientation By default, the Vision 90t/100t is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or mounted on a ceiling, you must change the picture orientation. To do this: 1.Press MENU and enter the Service Menu passcode. 2.Select Service from the Main Menu. 3.Select Display Device from the Service Menu. 4.Select Installation from the Display Device menu. 5.Choose Floor/Rear, Ceiling/Front or Ceiling/Rear, to match the installation method. Note You must enter a passcode to access the Service menu. 4.3 Lens Adjustments To access the motorized lens controls, select Display Device from the Service Menu, then select Lens from the Display Device menu. The Lens menu gives you a great deal of control over the picture size, position and focus: . Focus To focus the projected image, use the cursor buttons to highlight “In” or “Out.” Then, press and hold the ENTER button. . Zoom To make the picture smaller (zoom out), use the cursor buttons to highlight the minus sign (-). Then, press and hold the ENTER button. To enlarge the picture (zoom in), use the cursor buttons to highlight the plus sign (+). Then, press and hold the ENTER button. . Shift To change the projected image position, use the cursor buttons to highlight “Left,” “Right,” “Up” or “Down.” Then, press and hold the ENTER button to shift the image in that direction. 4.4 Using the On-Screen Menus Press the MENU button on either the remote control or the rear panel to display the Main Menu. To select a menu item, use the and buttons on either the remote control or the rear panel to highlight it. Press ENTER to confirm your selection. The Vision 90t/100t OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on the selected input source and signal characteristics, some menu options may not be available. CalibrationISF Night - Display ColorGainOffsetGammaLamp PowerColor Temp ISF Night - Input ImageBrightnessContrastColorTintSharpnessISF Night - Input ColorGainOffsetChroma DelayPhaseNoise FilterISF Day - Display ColorGainOffsetGammaLamp PowerColor TempISF Day - Input ImageBrightnessContrastColorTintSharpnessISF Day - Input ColorGainOffsetChroma DelayPhaseNoise FilterSave ISF SettingsBack / ConfirmOutput ShiftLeft/RightUp/DownWidthHeightSaveSplash ConfigureOwner NameISF CalibratedISF OtherOSD PositionServiceTest VideoGrey Bars 1Grey Bars 2Color Bars 1Color Bars 2Input NamesRename, Restore or SaveRemote ControlPrimarySecondaryDisplay DeviceInstallationPicture OrientationLamp Hours (View/Reset) LensFocusZoomShiftDiagnosticsRed OnlyGreen OnlyBlue Only75 IRE Color Bars100 IRE Color BarsHoriz. Grey RampVert. Grey RampCheckerboardAlignment GridHD FormatHD/RGB 1Auto, RGB or YUVHD/RGB 2ADC BandwidthAuto, 75 MHz, 150 MHz or 300 MHzYPbPr Input ResolutionAuto, 480i/p, 576i/p, 720p or 1080iTriggers1 / 2 / 3 / SaveMiscellaneousLanguage(currently, English only) Menu ModeTimeoutSide Bar ColorFilm Mode (SD src. only) Resolution800x600 ... 1400x1050 480i ... 720p ... 1080i System ResetRestore Saved SettingsNote: IntelliWide 2.35 is available only on Vision 90t/100t projectors equipped with the CineWide option (secondary anamorphic lens). Input SourceCompositeS-Video 1S-Video 2Component SDHD/RGB 1HD/RGB 2DVI 1DVI 2Aspect RatioAnamorphicStandard 4:3LetterboxIntelliWideCinemaIntelliWide 2.35PictureBrightnessContrastColorTintSharpnessInput PositionLeft/RightUp/DownWidthHeightOverscanISF PresetsRecall ISF NightRecall ISF DayRecall/Save Custom 1Recall/Save Custom 2Reset Custom 1 & 2 to Factory DefaultInformation(read-only) Serial NumberHardwareFirmwareDate Figure 4-1. Vision 90t/100t OSD Menu Structure Main . Menu The Main Menu is the starting point for accessing all projector functions. (The Calibration and Service menus are hidden and not accessible until you enter a passcode.) Input . Source From the Main Menu, select Input Source to choose a video signal source. The active source is indicated by an arro...

Ce manuel est également adapté pour les modèles :
TV - Vision 90t (4.17 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories