Example: ALAR:RHUM1:SENS:ENAB 1 The RHUMidity suffix, , specifies the channel (1 or 2). The parameter turns the humidity sensor alarm on (1 or ON) or off (0 or OFF). This command may be password protected (see Password Commands). ALARm:RHUMidity:UPPer? Indicates whether an upper humidity alarm event has occurred for the specified channel. Example: ALAR:RHUM1:UPP? Response: 0 The RHUMidity suffix, , specifies the channel (1 or 2). A value of 1 is returned if an upper humidity alarm event has occurred on the specified channel. A value of 0 is returned if an upper humidity alarm event has not occurred on the specified channel. ALARm:RHUMidity:UPPer:ENABle? Returns the state of the upper humidity alarm enable for the specified channel. Example: ALAR:RHUM1:UPP:ENAB? Response: 0 5020A Users Manual The RHUMidity suffix, , specifies the channel (1 or 2). A value of 1 is returned if the upper humidity alarm is enabled. A value of 0 is returned if the upper humidity alarm is disabled. ALARm:RHUMidity:UPPer:ENABle Sets the state of the upper humidity alarm enable for the specified channel. Example: ALAR:RHUM1:UPP:ENAB 1 The RHUMidity suffix, , specifies the channel (1 or 2). The parameter turns the upper humidity alarm on (1 or ON) or off (0 or OFF). This command may be password protected (see Password Commands). ALARm:RHUMidity:UPPer:LIMit? [MIN|MAX|DEF] Returns the upper humidity alarm limit for the specified channel in %RH. Example: ALAR:RHUM1:UPP:LIM? Response: 70.00 The RHUMidity suffix, , specifies the channel (1 or 2). Specifying the MIN, MAX, or DEF parameter returns the minimum, maximum, or default value respectively. ALARm:RHUMidity:UPPer:LIMit |MIN|MAX|DEF Sets the upper humidity alarm limit for the specified channel in %RH. Example: ALAR:RHUM1:UPP:LIM 65.00 The RHUMidity suffix, , specifies the channel (1 or 2). The parameter specifies the value for the upper humidity alarm limit. Specifying the MIN, MAX, or DEF parameter sets the upper humidity alarm limit to the minimum, maximum, or default value respectively. This command may be password protected (see Password Commands). ALARm:TEMPurature:LOWer? Indicates whether a lower temperature alarm event has occurred for the specified channel. Example: ALAR:TEMP1:LOW? Response: 1 The TEMPerature suffix, , specifies the channel (1 or 2).A value of 1 is returned if a lower temperature alarm event has occurred on the specified channel. A value of 0 is returned if a lower temperature alarm event has not occurred on the specified channel. ALARm:TEMPurature:LOWer:ENABle? Returns the state of the lower temperature alarm enable for the specified channel. Example: ALAR:TEMP1:LOW:ENAB? Response: 0 The TEMPerature suffix, , specifies the channel (1 or 2). A value of 1 is returned if the lower temperature alarm is enabled. A value of 0 is returned if the lower temperature alarm is disabled. ALARm:TEMPurature:LOWer:ENABle Sets the state of the lower temperature alarm enable for the specified channel. Digital Communications Interface Commands Example: ALAR:TEMP1:LOW:ENAB 1 The TEMPerature suffix, , specifies the channel (1 or 2). The parameter turns the lower temperature alarm on (1 or ON) or off (0 or OFF). This command may be password protected (see Password Commands). ALARm:TEMPurature:LOWer:LIMit? [MIN|MAX|DEF] Returns the lower temperature alarm limit for the specified channel in degrees C or F. Example: ALAR:TEMP1:LOW:LIM? Response: 18.00 The TEMPerature suffix, , specifies the channel (1 or 2). The value returned is always in the current temperature units (C or F). Specifying the MIN, MAX, or DEF parameter returns the minimum, maximum, or default value respectively. ALARm:TEMPurature:LOWer:LIMit |MIN|MAX|DEF Sets the lower temperature alarm limit for the specified channel in degrees C or F. Example: ALAR:TEMP1:LOW:LIM 20.00 The TEMPerature suffix, , specifies the channel (1 or 2). The parameter specifies the value for the lower temperature alarm limit. Specifying the MIN, MAX, or DEF parameter sets the lower temperature alarm limit to the minimum, maximum, or default value respectively. The value is always in the current temperature units (C or F). This command may be password protected (see Password Commands). ALARm:TEMPurature:RATE? Indicates whether a temperature rate alarm event has occurred. Example: ALAR:TEMP1:RATE? Response: 0 The TEMPerature suffix, , specifies the channel (1 or 2). A value of 1 is returned if a temperature rate alarm event has occurred on the specified channel. A value of 0 is returned if a temperature rate alarm event has not occurred on the specified channel. ALARm:TEMPurature:RATE:ENABle? Returns the state of the temperature rate alarm enable for the specified channel. Example: ALAR:TEMP1:RATE:ENAB? Response: 0 The TEMPerature suffix, , specifies...
)
Log: