Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
WARNING The monitor is not intended to be a diagnostic device. 10 BATTERY INSTALLATION BATTERY INSTALLATION CAUTION Use only 1.5V“AAA” alkaline batterieswith this device. 1. Press the hook on the bottom of the battery cover and lift the cover off in the direction of the arrow. 2. Install2“AAA”sizebatteriessothe+(positive)and ( negative) polarities match the polarities of the battery compartment as indicated. 3. Set the date and time. Refer to“Setting the DateandTime”. 4. Replace the battery cover. NOTE: Make sure that the battery cover is securely in position. 11 BATTERY INSTALLATION BATTERY INSTALLATION BATTERY REPLACEMENT Low Battery Indicator When the Low Battery Indicator appears on the display, turn the monitor off and remove all the batteries. Replace with 2 new batteries at the same time. Long-life alkaline batteries are recommended. WARNING If battery fluid should getin your eyes,immediatelyrinse with plenty of clean water. Contact a physician immediately. NOTES: • Turn the unit offbeforereplacing the batteries.Ifthebatteries are removed while the unit is still on, the date and time will be reset to that of the previous use. The measurement results are not deleted. • When the batteriesarereplaced,you may need to reset thedate and time. If the yearisflashing onthe display, refer to “SettingtheDate andTime”. • The batteries included with the device mayhave a shorter life. CAUTION Dispose of the device, components and optional accessories according to applicable local regulations. Unlawful disposal may cause environmental pollution. 12 SETTING THE dATE ANd TIME Set the monitor to thecurrent dateandtime beforetaking a measurementfor the first time. 1. TO START THE SETTING Press the Date/Time Setting button ( ) to adjust the date and time. Theyear flashes onthedisplay. 2. SETTING THE YEAR Press the Date/Time Setting button ( increments of one year. Press the Date/Time Setting button ( year. ) to advance by ) to set the current The month flashes on the display. NOTES: • Theyear can be setbetween 2009 and 2030. When the display reaches 2030, it will return to 2009. • Pressandhold the ( ) button to increase the date and time values faster. 3. SETTING THE MONTH Press the Date/Time Setting button ( ) to advance by increments of one month. Press the Date/Time Setting button ( ) to set the current month. Thedayflasheson the display. 13 SETTING THE dATE ANd TIME SETTING THE dATE ANd TIME 4. SETTING THE DAY Press the Date/Time Setting button ( ) to advance by increments of one day. Press the Date/Time Setting button ( ) to set the current day. Thehourflasheson the display. 5. SETTING THE HOUR The time is set using AM or PM. Press the Date/Time Setting button ( ) to advance by increments of one hour. Press the Date/Time Setting button ( ) to set the current hour. Theminuteflasheson the display. 6. SETTING THE MINUTE Press the Up button ( ) to advance by increments of one minute. Press the Date/Time Setting button ( ) to set the minute setting. 7. TO TURN THE MONITOR OFF Press the START/STOP button. 14 SETTING THE AdVANCEd POSITIONING SENSOR (APS) SETTING THE AdVANCEd POSITIONING SENSOR (APS) You can change the options for various settings on your monitor. Pressing the SET button to change a setting. Press the MEM button to select the options for that setting. After selecting a setting, press the START/STOPbuttonto confirm the settingandturn the power off. SETTING THE POSITIONING INDICATOR 1. Select your User ID. 2. Press the SET button. NOTE: The default settingis“on1”. User A User B 3. PresstheMEMbuttontoselectthePositioningindicator“on1”,“on2”,or“oFF”. on1: After the Positioning indicator lights in blue for more than 2 seconds, or in orange for more than 5 seconds, measurement starts automatically, even though the monitor is not in the proper position. on2: The Positioning indicator lights in blue for more than 2 seconds, measurement starts automatically. Measurement will not start if it lights in orange. oFF: Measurement starts without the Positioning indicator. 15 16 SETTING FOR RIGHT OR LEFT WRIST MEASUREMENT 1. While in the setting mode, press the SET button until the wrist symbol ( or ) appears on the display. NOTES: • The default setting is “ ”. • After you choose “oFF” for the Positioning indicator, the monitor skips this process. 2. Press the MEM button to select the left wrist ( ) or the right wrist ( ). SETTING THE BUZZER 1. While in the setting mode, press the SET button until the buzzer symbol ( ) appears on the display. NOTE: The default setting is “on1” or “on”, depending on the Positioning indicator you set. 2. Press the MEM button to select the buzzer setting. SETTING THE ADVANCED POSITIONING SENSOR (APS) SETTING THE AdVANCEd POSITIONING SENSOR (APS) SETTING THE AdVANCEd POSITIONING SENSOR (APS) IfthePositioning indicatoris “on1”or “on2”: on1: The buzzer sounds only when the monitor is in proper position. on2: The buzzer sounds a series of two short blips if your wrist is too far away from the me...