Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Follow the directions of your doctor. AVERAGE VALUE SYMBOL (M ) The Average Value Symbol is displayed if the measurement values displayed are an average of up to three measurements taken within 10 minutes of the last reading. MOVEMENT ERROR SYMBOL ($ ) The Movement Error Symbol is displayed if you move your body during the measurement. Please remove the arm cuff, and wait 2-3 minutes. Take another measurement. Normal Heartbeat Pulse JUULAJUL Blood JVfVJVJMVA pressure Irregular Heartbeat Short Long Pulse JULAULZJUL Blood pressure 10 DISPLAY SYMBOLS The American Heart Association1 recommends the following guideline for upper limit of normal for home blood pressure readings: AHA Home Guideline for Upper Limit of Normal BP Systolic Blood Pressure 135 mmHg Diastolic Blood Pressure 85 mmHg This is a general guideline because blood pressure depends on age and morbidity. The AHA recommends a lower home blood pressure goal for certain patients, including diabetic patients, pregnant women, and patients with renal failure1. The monitor is not intended to be a diagnostic device. WARNING Contact your physician for specific information about your blood pressure. Self-diagnosis and treatment using measured results may be dangerous. Follow the instructions of your physician or licensed healthcare provider. Omron Healthcare recommends you contact your physician if the HEARTBEAT SYMBOL appears on the display with your measurement values. HEARTBEAT SYMBOL (# ) TAKING A MEASUREMENT The Heartbeat Symbol flashes on the display during the measurement.The Heartbeat Symbol flashes at every heartbeat. When the measurement is complete, the Heartbeat Symbol flashes on the display with your blood pressure and pulse rate if the reading is above 135 for the Systolic Blood Pressure value and/or 85 for the Diastolic Blood Pressure value. 11 DISPLAY SYMBOLS USING THE MEMORY FUNCTION The Heartbeat Symbol flashes when the blood pressure reading stored in the memory is above 135 for the Systolic Blood Pressure value and/or 85 for the Diastolic Blood Pressure value. 12 BATTERY INSTALLATION 1. Press the ▼ indicator on the battery cover and slide the cover off in the direction of the arrow. 2. Install 4 “AA” size batteries so the + (positive) and - (negative) polarities match the polarities of the battery compartment as indicated. 3. Replace the battery cover. J ) t ) 13 Battery Cover BATTERY INSTALLATION BATTERY REPLACEMENT « Low Battery Indicator When the Low Battery Indicator appears on the display screen turn the monitor off and remove all the batteries. Replace with four new batteries at the same time. Longlife alkaline batteries are recommended. A CAUTION If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Contact a physician immediately. NOTES: • Turn the unit off before replacing the batteries. If the batteries are removed while the unit is still on, the date and time will be reset to that of the previous use. However, the measurement results are not deleted. • When the batteries are replaced, you may need to reset the date and time. If the year is flashing on the display screen, refer to page 16, SETTING THE DATE AND TIME. A CAUTION Dispose of the device, components and optional accessories according to applicable local regulations. Unlawful disposal may cause environmental pollution. 14 USING THE AC ADAPTER NOTES: • Use only the authorized Omron AC Adapter, Model Number HEM-ADPT1,with this monitor. • We recommend you install the batteries even if the AC Adapter is used. If no batteries are installed, you may need to reset the date and time if the AC Adapter is disconnected. The measurement results will not be deleted. A CAUTION Use only Omron authorized parts and accessories. Parts and accessories not approved for use with the device may damage the unit. TO CONNECT THE AC ADAPTER ® Insert the AC Adapter Plug into the AC Adapter Jack on the back side of the monitor as illustrated. ® Plug the AC Adapter into a 120V AC outlet (60 cycles). TO DISCONNECT THE AC ADAPTER Housing (2 X U Cord ® Hold and pull the Housing to remove the AC Adapter from the electrical outlet. Do not remove by pulling on the cord. ® Remove the AC Adapter plug from the monitor. WARNING Do not plug or unplug the power cord into the electrical outlet with wet hands. A CAUTION Do not overload power outlets. Plug the device into the appropriate voltage outlet. 15 SETTING THE DATE AND TIME Set the monitor to the current date and time before taking a measurement for the first time. If the date and time are not set correctly, the measurement values stored in the memory and the average values may not be correct. The Blood Pressure Monitor automatically stores up to 60 individual measurements values with the dates and times. The monitor can also calculate an average reading based on the three most recent measurements taken within 10 minutes of the last reading. NOT...