Évaluations - , GPA: ( )

Instructions Omron, Modèle 11 685

Fabricant : Omron
Taille : 420.18 kb
Nom Fichier : square-face-wall-aneroid-instruction-manual.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Attach one end of the coiled to the connector on the underside Aneroid (Figure 2). 2. Attach the other end of the coiled the metal connector) to the tube from and bladder (the tube without the bulb assembly). Figure 5 3. The cuff and bladder assembly can be stored in the basket on the back of the aneroid. Once mounted to the wall or affixed to a floor stand, the Omron Aneroid is ready for use. Connector Wall-Mount (for models 11-675D and 11-675DNL) : Coiled Tube 1. Hold wall-mount plate against the wall at the desired location and mark the position of the mounting holes for drilling. Drill four (4) holes and insert the metal wall anchors. Attach the wall-mount plate to the wall by using the four metal (4) screws (Figure 3). 2. Loosen wing nut on the bottom of the Aneroid and adjust the unit to the desired angle. Tighten wing nut and slide the wall bracket into the wall-mount plate (Figure 4). Figure 4 3. The wall-mounted Omron Aneroid is now ready for use. Figure 3 Figure 2 240 240 220 180160140 120 100 80 60 40 20 260 280 300 mmHg SPHYGMOMANOMETER CERTIFIED MADE IN JAPAN Air Release Valve Bulb 4 5 ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS Floor Stand Kit models 11-685 Figure 6 Figure 7 1. Insert each of the five (5) wheel casters into each (5) legs of the five-legged base (Figure 6). 2. Insert the larger diameter chrome plated pole five-legged base. 3. Insert the large hex-bolt, the large washer, and one small washer from the bottom center of the five-legged base into the bottom center of the larger diameter chrome plated pole. Securely tighten bolt. 4. Insert the smaller diameter chrome plated pole into diameter pole. Insert the black knob into the top of the diameter pole. Set the smaller diameter pole to the desired height the black knob. 5. The floor stand is now complete. To attach the Omron Aneroid to the floor stand, begin by removing the wing nut connecting the aneroid to the wall-mount bracket (Figure 7). 6. Insert the small hex nut from the Omron Aneroid and one small washer from the top of the hole where the wing nut was removed. 7. While holding the aneroid and small hex nut assembly in one hand, insert the small hex nut into the top of the smaller diameter chrome plated pole. Turn the pole counter-clockwise to attach both assemblies. Securely tighten the assembly. 8. The floor-mounted Omron Aneroid is now ready for use. On-Site Calibration: 1. Remove the coiled tube from the connector on the underside of the aneroid. 2. Insert the calibration tool (or small flat-head screw driver) into the connector (from where the coiled tube was removed). 3. Turn the calibration tool until the needle on the front of the gauge is centered at the bottom of the gauge. 6 7 240 240 220 180160140 120 100 80 60 40 20 260 280 300 mmHg SPHYGMOMANOMETER CERTIFIED MADE IN J A PA N Sphygmomanometer Five-Legged Base Large Washer Small Washer Large Hex Bolt Wheel Casters Small Diameter Chrome-Plated Pole Large Diameter Chrome-Plated Pole Black Knob OMRON HEAL...