Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
are not possible. PROGRAMMING TAX TABLE (Condition: after an AUTO SCAN RESET) Mode Lock: SET 1) TAX 1 FULL BREAKS Key Operation: -|max. amount non-taxable [ —* ITX1/M1 |max, amount for 1^ tax levied 1 —»ITXl/Ml |max. amount for tax levied) —>1TX1/M~1 Repeat until the "A" Break is entered. jmax. amount for tax levied|—»TTXI/Ml..."A" Break 1ST I (to indicate the "A" Break entry) [max. amount for fj+1^ tax leviedj—>|TX1/Mj |max. amount for N+2^ tax levied| —>|TXl/MI Repeat until the "B" Break is entered. IAT/TL! (to end) NOTE: The amount entry may be maximum 4-digit value (up to 9999*5). 2) TAX 1 "A*1 BREAK AND % RATE COMBINATION Key Operation: First set the "A" Break following the same operation up to the "A" Break entry and the |ST I key depression in "1) TAX 1 FULL BREAKS" above. I |TAX RATE applied when exceeding the "A" Break amount! (max, 4 digits, up to 99.99%. Do not use the [7] key. The fraction of the amount resulted from this % rate calculation will be rounded off.) I IAT/TLI (to end) 3) TAX 1 % RATE ONLY Key Operation: 101 -» i TXl/Ml-» I ST I —>I TAX RATE I—»lAT/TLl " (The conditions of the rate are the same as the above TAX RATE.) NOTES: 1. If only one tax modifier key ( 1 TX/Ml ) is installed on the keyboard, use the ITX/MI in place of the I TXl/M I in the description 1), 2), or 3) above. on 2. For TAX 2 Table programming, follow the same procedure in thide 1), 2), or 3) above, using the ITX2/MI instead of the ITXl/Ml. 3. If both TAX 1 and TAX 2 tables are programmed, the TAX 1 must be set first. The TAX 1 table entry will automatically reset both the TAX 1 and TAX 2 tables that have been programmed. 4. No second depression of the I ST I key is allowed within one tax table programming. SETTING NON-TAXABLE LIMIT AMOUNT (for a certain area only) (Condition: after an AUTO SCAN RESET) This may be programmed only when one tax modifier key ( ITX/MI) is installed. The tax levied when exceeding this limit amount will be calculated by the TAX 1 table. Mode Lock: SET Key Operation: )91 —» ■ [x] —»1 Non-taxable Limit Amount[—»IAT/TL1 NOTES: 1. If this program has been set, the tax is calculated and added to the sale total which exceeds the limit amount even when the sale is entirely composed of non-taxable items, 2. To reset the limt amount once set, enter "0" in place of the ]Non-taxable Limit Amount 1 in the above operation. 3. This tax calculation program will be disregarded when the sale total turns out to be negative. ex.) In case the limit amount "$3.25" is set: Case 1: Normal Department Entry: (Mode Lock: REG) |3261 —»Inon-taxable DEPT| -> IAT/TL1 ..... The entered amount $3.26 is greater than the limit amount $3.25. It will therefore be taxed. Case 2: Returned Merchandise Entry: (Mode Lock: REG) IRTN MDSEl-»|3261 -»[non-taxable DEPT|->|AT/TL1 ..... The non-taxable total is negative. The tax already levied will therefore not be returned. sale) '0", the iove in the )pen CZXk] rice tfith ined ning SETTING THE LISTING CAPACITY OF DEPARTMENT (Condition: after an AUTO SCAN RESET) Mode Lock: SET Key Operation *(Note 1) _ |2| -> [x] |HALC| * IAT/TLI ... for the common listing capacity for all the departments HNote 1)_ [2 i -» fxl •» | HALC 1 | DEPT j -» | AT/TL | ... for individual departments LI listing capacities Repeat until all-* the required indiv. dept. Listing Capacities are set. ♦Note 1: HALC ..... Hight Amount Listing Capacity ■Number of maximum digits allowed ■Maximum value of the ,top digit .allowed ex.) )3|4| ... indicates 3999 -r The amount range allowed !■—-4 digits — '—Value of the to enter will be: j. ■*. Equal to or smaller than 1®1 the HALC (3999 in this case) NOTES: 1. If the individual listing capacity of a department has been set, it prevails over the common listing capacity of all the departments. 2. To reset an individual listing capacity, enter "0" beioxe the [DEPTI key in the above operation. Then the common listing capacity of all the departments, if pre-programmed, will prevail. SETTING THE PRESET RATES OF [¡[T] AND [&3 KEYS (Condition: anytime outside a sale) Mode Lock SET Key Operation 1) To set a rate of integral value: | RATE | -» [%+1 | RATE | f [%3 2) To set a rate containing the decimal point: | Integral Portion! [~!~1 |Decimal Portion! r* !%+1 max. 2 digits max. 3 digits I (up to 99.999%) 3) To reset the rate once set: |0| ♦ [%3 |0| [%3 - 31 - SETTING HOURLY RANGES (Condition: after an AUTO SCAN RESET) Mode Lock: SET l£| № NOTES: 1. 2. 3. 4. Key Operation (0-23) (01-59) I HOUR IMINUTE I S3 IAT/TLI Enter the time to end each hourly range, in the 24-hour system. __ Repeat until all the time ranges are entered. A maximum of 16 hourly ranges may be set. To change the table of hourly ranges once set, partially or entirely, do the entire setting operation over again. To reset the hourly range table once set: Mode Lock: SET, Ml ♦fxUloUfTI-»Fat7tl1 Do not set an hourly range accros...
Ce manuel est également adapté pour les modèles :Shop Equipment - MA-136 (1.22 mb)