Évaluations - 2, GPA: 4 ( )

Fabricant : Toshiba Taille : 1.69 mb Nom Fichier : Langue d'enseignement:

P o w e r Co rd 3. Plug the other end of the Power Cord into the ground outlet as shown in the figure below. P o w e r Co rd 2- 3 2. PRINTER SETUP EO1-33030 2.5 Turning the Printer ON/OFF 2.5 Turning the Printer ON/OFF 2.5.1 Turning ON the Printer CAUTION! Use the Stand-by switch to turn the printer On/Off. Plugging or unplugging the power cord to turnthe printer On/Off may cause fire, an electric shock, or damage to the printer. NOTE: When the ERROR LED is illuminated, refer to Section 4.1 LED State. 2.5.2 Turning OFF the Printer CAUTION! 1. Do not turn off the printer power while the media is being printed as this may cause a paper jam or damage to the printer. 2. Do not turn off the printer power while the ON LINE light is blinking as this may cause damage to your computer. When the printer is connected to your host computer it is good practice to turn the printer ON before turning on your host computer and turn OFF your host computer before turning off the printer. 1. To turn ON the printer power, slide the Stand-by switch as shown in the diagram below. Note that ( l ) is the power ON side of the switch. ON Stand-by Switch 2. Check that the ON LINE LED is illuminated. 1. To turn OFF the printer power, slide the Stand-by switch as shown in the diagram below. Note that no mark is printed on the power OFF side. OFF Stand-by Switch 2- 4 2. PRINTER SETUP EO1-33030 2.6 Opening/Closing the Media Cover 2.6 Opening/Closing the Media Cover WARNING! The Media Cover should be opened fully. Failure to do this may cause the Media Cover to close by its weight, resulting in injury. This section describes the opening and closing procedure of the Media Cover. Follow the procedure when cleaning the print head, platen, paper passage, or media sensor, or removing jammed paper. Opening the Media Cover 1. Release the Media Cover by pushing both sides of the Media Cover Release Catches toward the center, and then open the Media Cover. Media Cover Media Cover Release Catch Media Cover Release Catch Closing the Media Cover 1. Close the Media Cover by pressing portions (A) until they click. 2. Make sure that both Media Cover Release Catches are in position and the Media Cover is locked. Media Cover Media Cover Release Catch (A) Media Cover Release Catch (A) 2- 5 2. PRINTER SETUP EO1-33030 2.7 Loading the Media 2.7 Loading the Media The B-419 printer issues in two issue modes depending on the media types. Continuous mode (Fanfold paper) • Insert the media through the media inlet, or open the media cover and set the media, and then close the media cover. • When the print command is received from the PC, the specified numbers of media are printed continuously. • Pressing the [FEED] button causes one piece of media to be fed. Cut form mode (When the auto-feed is turned ON.) • Insert the media through the media inlet, or open the media cover and set the form, and then close the media cover. The media is automatically fed to the print start position. • When the print command is received from the PC, the specified numbers of media are printed one by one. • When unprinted data remains after issuing the media, the DATA LED flashes slowly (indicating the printer is waiting for media supply.) • Pressing the [FEED] button causes one piece of media to be fed. 2- 6 2. PRINTER SETUP EO1-33030 2.7 Loading the Media 2.7.1 Loading the Fanfold 1. Place the fanfold paper at the rear of the printer in line. Paper Container 2. Place the paper top edge in front of the Media Inlet, and align the left paper edge with the Paper Guide (L). Push the Paper Guide Release Lever outside, and align the Paper Guide (R) with the right paper edge. 3. Lock the Paper Guide by pulling the Paper Guide Release Lever up. Release Lever Paper Guide (R) 4. Turn the PC power ON, and then turn the printer power ON. 5. Insert the paper top edge into the Media Inlet until it stops. Pressing the [FEED] button feeds one piece of the paper. 6. Send a print data from the PC. 7. The data is printed on the paper. Tear off the printed paper at the edge of the Media Outlet. NOTE: Do not pull the printed paper. Doing so may dislocate the printer or misalign the print position, causing a print failure. Paper Guide (L) Paper Guide Lock Release NOTES: 1. Place the fanfold paper so that the print surface faces up and the top edge of the paper is positioned at the printer side. 2. Place the fanfold paper on the surface below the position of the printer’s media inlet. Print Surface Paper Top Edge Media Inlet Fanfold Paper 2- 7 2. PRINTER SETUP EO1-33030 2.7 Loading the Media 2.7.2 Loading the Cut Form 1. Place the paper top edge in front of the Media Inlet, and align the left paper edge with the Paper Guide (L). Push the Paper Guide Release Lever outside, and align the Paper Guide (R) with the right paper edge. NOTE: The AUTO FEED function is available when selected by the printer setting and black marks are printed on the media as shown below. For details of the printer setting, please conta...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :