Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
Media Guide Media Guide Adjustment Dial 8. Push the Media Holders against the media roll to firmly hold it, then slide the Media Holder Lock Switch to the Lock (Ў) side. Media Holder Lock Switch E2- 9 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media (Cont.) 9. Close the Top Cover gently and push down the arrow-indicating portions until they click. CAUTION! To separate the printed media from the media roll in batch mode, be sure to tear off the media at the Media Outlet or cut the media past the Strip Plate. If you tear off the media at the Print Head by mistake, be sure to feed one label (10 mm or more) with the FEED Button prior to a next issue. Failure to do this may cause a paper jam. 10. Press the [FEED] button to check for a proper media feed. FEED Button There are three issue modes available for this printer. Batch mode: In the batch mode, the media is continuously printed and fed until the number of media specified in the issue command has been printed. E2-10 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media (Cont.) NOTES: 1. When issuing labels without removing them from the backing paper, it is not necessary to pass the media through the Strip Block. 2. When the media is correctly set, the backing paper is supposed to be pinched by the Platen and the Strip Feed Roller as shown below. Strip Feed Roller Platen Strip Plate Label Backing Paper 3. If the peel-off issue is performed under intense light, the strip sensor may not correctly detect the presence of a printed label on the strip shaft. In this case, reduce the intensity of the light or fit the Shade Plate to the Strip Block as shown in the figure. Shade Plate Strip mode (Option): When issued in the strip mode, labels are automatically removed from the backing paper each time a label is printed. • How to set the media When issuing labels in the strip mode, set the label in the following procedure: 1. Load the media as described on the previous pages. 2. Open the Strip Block by pulling it out. Strip Block 3. Remove enough labels from the leading edge of the media to leave 20 cm of backing paper free, and insert the top edge of the backing paper into the media slot in the Strip Block. 4. Close the Strip Block and Top Cover. E2-11 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media (Cont.) NOTE: When placing fanfold paper stock on the rear of the printer, the following care should be taken. 1. Face the print surface up. 2. The fanfold paper stock is parallel to and level with the fanfold paper slot. 3. Interface cables do not interfere with the feed of fanfold paper. WARNING! HAZARDOUS MOVING PARTS KEEP FINGERS AND OTHER BODY PARTS AWAY The cutter is sharp, so care must be taken not to injure yourself when handling the cutter. CAUTION! 1. Be sure to cut the backing paper of the label. Cutting labels will cause the glue to stick to the cutter which may affect the cutter quality and shorten the cutter life. 2. Use of tag paper of which thickness exceeds the specified value may affect the cutter life. Cut mode (Option): When the Cutter is installed, the media is automatically cut. After loading the media as described on the previous pages, insert the leading edge of the media through the Media Outlet of the Cutter Cover. Cutter Cover Media Outlet How to Load Fanfold Paper Stock 1. Place the fanfold paper stock on the rear of the printer, and insert the leading edge of the paper into the Fanfold Paper Slot. Fanfold Paper Stock Fanfold Paper Slot 2. Refer to the previous pages to feed the fanfold paper through the printer until it extends past the media outlet. E2-12 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.7 Loading the Media 2.7 Loading the Media When a media roll has an outside diameter exceeding 127 mm (5”) and the inner core diameter of 76.2 mm (3”), the optional External Media Roll (Cont.) Hanger is required. 1. Fit the protrusions on the bottom of the printer into the holes in the External Media Roll Hanger. External Media Roll Hanger (Option) 2. Insert the Media Shaft into the core of the media roll. 3. Place it into the cuts of the External Media Roll Hanger. 4. Pull the media forward and insert the leading edge into the Fanfold Paper Slot. Media Shaft (Option) Fanfold Paper Slot 5. Refer to the previous pages to complete the media loading. 6. Close the Top Cover. E2-13 2. PRINTER SETUP ENGLISH VERSION EO1-33088 2.8 Media Sensor Calibration, Self Print Test, and Dump Mode Utilities This utility is used to calibrate the sensitivity of the Feed Gap/Black 2.8 Media Sensor Mark Sensor. Calibration, Self Print It is necessary to set the media sensors after the media is changed to Test, and Dump Mode different type. Utilities 2.8.1 Media Sensor 1. First, select the sensor to calibrate in the following procedure. Calibration Turn on the printer power. NOTE: The sensor type used in the last print job has been selected. The factory default i...
Ce manuel est également adapté pour les modèles :Shop Equipment - B-EV4D SERIES (1.24 mb)