Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Shop Equipment - PT-2730 (4.57 mb)
Shop Equipment - PT-2730 (4.93 mb)
Facilité d'utilisation
2 Insert the AC adapter plug into a standard electrical outlet. • Turn the P-touch labeler off before disconnecting the AC adapter. • Do not pull or bend the AC adapter cord. To safeguard and backup the labeler's memory and clock setting, when the AC adapter is unplugged it is recommended to have AA-size alkaline batteries (LR6) installed into the machine. WARNING • • Use only the adapter, which is designed exclusively for your P-touch. Failure to observe this may result in an accident or damage. Brother shall not assume any responsibility for any accident or damage resulting from not using the specified AC adapter. Do not connect the AC adapter to a non-standard electrical outlet. Failure to observe this may result in an accident or damage. Brother shall not assume any responsibility for any accident or damage resulting from not using a standard electrical outlet. CAUTION • • Disconnect the AC adapter from the P-touch and electrical outlet when you do not intend to use the P-touch for an extended period. When power is disconnected for more than two minutes, all text and format settings will be cleared. Any text files stored in the memory will also be cleared. 17 Power Supply 1 2 3 4 5 6 7 8 9 18 .. GETTING STARTED Inserting a Tape Cassette Tape cassettes of 0.13", 0.23", 0.35", 0.47", 0.70" or 0.94" (3.5mm, 6mm, 9mm, 12mm, 18mm, or 24mm) width can be used in your P-touch labeler. Use only Brother tape cassettes with the mark. Check that the end of the tape is not bent and that it passes through the tape guide. If the tape is not passed through, pass it through the tape guide referring to the illustration. After making sure that the power is off, lift open the tape compartment cover. If there is already a tape cassette in the machine, remove it by pulling it straight up. Inserting a Tape Cassette • If the new tape cassette has a cardboard stopper, be sure to remove the stopper before inserting the cassette. • If the ink ribbon is loose, use your finger to wind the toothed wheel in the direction of the arrow as shown on the tape cassette. End of tape Tape guide 1 2 GETTING STARTED 3 Insert the tape cassette into the tape compartment, with the end of the tape facing the machine's tape exit slot, and press firmly until you hear a click. When inserting the tape cassette, make sure that the tape and ink ribbon do not catch on the print head. Tape exit slot 4 Close the tape compartment cover. Make sure that the release lever is up when closing the tape compartment cover. The tape compartment cover cannot be closed if the release lever is pressed down. • Be sure to feed tape to remove any slack in the tape and ink ribbon after inserting the tape cassette, by holding down the Shift key and pressing the Preview key. • Do not pull the label coming out of the tape exit slot. Doing so will cause the ink ribbon to be discharged with the tape. • Store tape cassettes in a cool dark location, away from direct sunlight and high temperature, high humidity, or dusty locations. Use the tape cassette as quickly as possible after openingthe sealed package. Turning Power On/Off Press the Power key to turn the P-touch labeler on. Press the Power key again to turn the P-touch labeler off. • Your P-touch labeler has a power saving function that automatically turns itself off if no key is pressed within a certain time under certain operating conditions. Refer to the Auto Power- Off Time table below for details. • If the batteries are installed or the P-touch labeler is connected to an electrical outlet by theAC adapter, the previous session’s information is displayed when the power is turned on. ..Auto Power-Off Time• P-touch labeler only Connected to PC With AC adapter 8 hours 8 hours With battery 5 minutes No operation for 1 hour after connection to USB. 19 Turning Power On/Off Feeding Tape .. GETTING STARTED Feed & Cut The Feed & Cut function feeds 0.92" (23mm) of blank tape then cuts the tape. • Be sure to feed tape to remove any slack in the tape and ink ribbon after inserting the tape cassette. • Do not pull the label coming out of the tape exit slot. Doing so will cause the ink ribbon to be discharged with the tape. • Do not block the tape exit slot during printing or when feeding tape. Doing so will cause the tape to jam. 1 Hold down the Shift key and press the Preview key. "Feed & Cut?" will appear on the LCD display. 2 Using the or key to select the "Feed & Cut" option and then press either OK or Enter. The message "Feeding Tape... Please Wait" appears while the tape is fed, and then the tape is cut. To exit or cancel this function press Escape. Feed Only This function will advance the tape approximately 0.92" (23 mm) resulting in a blank label sticking out of the tape cassette. This action is recommended when using Fabric and Extra Strength Adhesive tapes, which should be cut using scissors. 1 Hold down the Shift key and press the Preview key. "Feed & Cut?" will appear on the LCD display. 2 Using the or key to select the "...