Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• To prevent fi re or electric shock, make sure that the plug is fully inserted to the power outlet. Do not use an outlet that is loose. • Do not get the machine/AC adapter/power plug wet, such as by handling them with wet hands or spilling beverages on to them. • Do not disassemble or modify P-touch labeler/AC adapter/batteries. • Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the batteries. • Do not throw into fi re or heat up the battery. • Disconnect the AC adapter, remove batteries and stop using immediately if you notice any abnormal odor, heat, discoloration, deformation or anything unusual while in use, or in storage. • To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the print head. • Remove the batteries and disconnect the AC adapter if you do not intend to use P-touch labeler for an extended period of time. • Do not use old and new batteries together or mix alkaline batteries with other type batteries, or set the positive and negative end in the wrong position. Otherwise, the batteries may leak or be damaged. • To prevent damage or breakage, do not drop or hit P-touch labeler/AC adapter. • Use only the USB cable included with the P-touch labeler. • Depending on the location, material, and environmental conditions, the label may unpeel or become irremovable, the color of the label may change or be transferred to other objects. Before applying the label, check the environmental condition and the material. • Do not use the P-touch labeler in any way or for any purpose not described in this guide. Doing so may result in accidents or damage the machine. • Use only Brother TZ tapes with this machine. Do not use tapes that do not have the mark. • Do not clean P-touch labeler with alcohol or other organic solvents. Only use a soft, dry cloth. • Do not touch the print head with your fi ngers anytime to prevent from a burn. Use a soft wipe (e.g. a cotton swab) when cleaning the print head. • Do not put any foreign objects into the tape exit slot or AC adapter connector, etc. • Do not place the P-touch labeler/battery in direct sunlight or rain, near heaters or other hot appliances, in any location exposed to extremely high or low temperatures (e.g. on the dashboard or in the back of your car), high humidity, or dusty locations. • Do not try to print labels using an empty tape cassette in the P-touch labeler. Doing so will damage the print head. • Do not pull the tape being fed from the P-touch labeler, otherwise the tape cassette or P-touch labeler may be damaged. Insert a tape cassette. Close the cassette cover. Verify that the P-touch labeler is turned off. Open the cassette cover as shown by the arrow in the above illustration while pressing the part marked "<<". Insert a tape cassette as shown in the above illustration. • Make sure that the end of the tape feeds under the tape guides. • If the ink ribbon is loose, use your fi nger to wind the toothed wheel in the direction of the arrow on the cassette. • Use only Brother tapes with the P-touch labeler. • For initial use of the tape, install the tape. Then, push in the Feed & Cut button to cut the tape. • Make sure that the release lever is up when closing the tape cover. The tape cover cannot be closed if the release lever is pressed down. Connect the P-touch labeler's power supply. When using the included AC adapter (AD- 24ES), insert the plug on the adapter cord into the adapter jack on the bottom end of the P-touch labeler. Insert the plug into the nearest standard electrical outlet. Auto Power Off Function When the P-touch labeler is operating on battery power only, it will turn off automatically if not used for a period of 20 minutes. The message “Unsafe Removal of Device” may be displayed depending on the Operating System running on your PC. Any data being displayed will be saved. When you turn the labeler back on, click on the Editor Lite icon to resume creating your label. Connect the USB cable and start P-touch Editor Lite. When using Windows Vista® When connecting the device for the fi rst time, perform the scan and then select the Always do this for software and games check box on the dialog box displayed when the scan completes. P-touch Editor Lite will start automatically the next time you connect the P-touch labeler. How to disconnect the P-touch labeler If you would like to use the more advanced software that is available for your P-touch labeler, you are able to install P-touch Editor 5.0 from the included CD-ROM. This advanced software will give you greater label making functionality. Do not connect the P-touch labeler to your PC before you begin the P-touch Editor 5.0 installation. For details on how to install P-touch Editor 5.0, see the installation guide in the included CD-ROM. Starting P-touch Editor 5.0 Review the names of P-touch labeler parts. Install a tape cassette. The PT-2430PC has 2 mode selector settings - “EL” and “E”. The mode selector switch is pre-...