Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
Place the cash register on a stable, flat surface not subject to direct sunlight. 1 Connecting the Barcode Scanner A barcode scanner is provided with the cash register. To use the scanner, connect the scanner before turning on the register. 1. Open the Scanner port cover at the right side of the register. 2. Insert the connector of the barcode scanner into the Scanner port, and tighten both screws on the connector. CAUTION: • Always unplug the power cord of the cash register when you connect or disconnect the barcode scanner. • Never connect devices other than the barcode scanner before changing the interface setting. Otherwise malfunction of the cash register will occur. 3 Preparing the Cash Register 1. Push the printer cover forward and detach it. 2. Remove the white retainer at the position shown right. NOTE: Please keep this retainer for future use when transferring the cash register. 3. Move the print head release lever upwards as illustrated right. 2 Initializing the Cash Register To ensure the cash register operates properly, please use the following procedure: 1. Make sure the power cord plug is not inserted into the AC outlet. 2. Insert the manager (MA) key into the mode switch and turn it to the PGM position. 3. While holding down both the }key and the lkey, insert the plug into the AC outlet. The buzzer will sound three times and “***MRS.***” will be displayed. 4. The cash register has now been initialized. The register display will show “0.00” with “PGM”. CAUTION: To charge the rechargeable batteries, keep the power on for one or two days. Leave the register with the mode switch in a position other than “OFF”. NOTE: If you press a key by mistake, an error message may be displayed. Press the lkey to clear message after installing paper rolls. 4 Installing the Paper Rolls 1. Cut off approximately one revolution of each paper roll. Make sure the paper end is cut as illustrated right. For receipt paper installation 2. Set a paper roll in the paper cradle of the receipt side (upper side) as illustrated right. 3. Insert the end of the paper into the paper chute until it is caught by the printer auto-feed and comes out the top of the printer. If the printer does not catch the paper, feed the paper while pressing }. 4. Cut off the excess paper with the paper cutter. For journal paper installation 5. Set a paper roll in the paper cradle of the journal side as illustrated in step 2. 6. Insert the end of the paper into the paper chute until it is caught by the printer auto-feed and comes out the top of the printer. If the printer does not catch the paper, feed the paper while pressing }as illustrated in step 3. 7. Insert the end of the paper into the slit in the take-up spool and fold the paper to front side, then wind the paper two or three turns around the spool shaft. (Press } to feed more paper if required.) 8. Set the spool on the bearing, and press the }key to take up excess slack in the paper. 9. Replace the printer cover. REG OPX/Z MGR PGM X1/Z1 X2/Z2 OFF VOIDMA Retainer Print head release lever Slit Correct Incorrect To the printer Incorrect To the printer Correct 5 Basic Programming Set the mode switch to the PGM position. Setting the Date Enter the date in 8 digits using the month-day-year format. Then press s. Example: 02262010sDate (February 26, 2010) Setting the Time Enter the time in 4 digits (“hhmm” format) using the 24 hour system. Then press s. Example: 1430sTime (2:30 p.m.) Setting Tax Rates (%) NOTE: If you are in an area that uses a tax table for tax calculation, please refer to the programming section in the instruction manual. Specify a tax rate (%) for calculation of tax on each taxable subtotal using the following sequence: s. 9. @. Tax number (1 to 4) . @. Tax rate (0.0000% to 100.0000%) . @ . Minimum taxable amount (0.01 to 999.99) . s. A(Smallest amount for which tax must be collected.) NOTE: Up to 4 types of tax are programmable for Tax 1 through Tax 4. Example1: Set state tax 6.25% with tax exempt as 12. s9@1@6P25@12sATax 1 Tax rate (6.25%) Min. taxable amount ($0.12) Example2: Set state tax 4% with tax exempt as 0. s9@1@4sATax 1 Tax rate (4%) Other Programming The cash register is pre-programmed so it can be used with minimal set-up. For optional features, please refer to the instruction manual. Initial settings: Department 1 to 10: Taxable 1 Department 11 to 99: Non-taxable NOTE: To scan barcodes using the barcode scanner, their preset unit prices, associated departments and item labels should be programmed. REG OPX/Z MGR PGM X1/Z1 X2/Z2 OFF VOID 5 Basic Programming Set the mode switch to the PGM position. Setting the Date Enter the date in 8 digits using the month-day-year format. Then press s. Example: 02262010sDate (February 26, 2010) Setting the Time Enter the time in 4 digits (“hhmm” format) using the 24 hour system. Then press s. Example: 1430sTime (2:30 p.m.) Setting Tax Rates (%) NOTE: If you are in an area that uses a tax table for tax calculation, please refer to t...