ENTER/EXIT PROGRAMMING MODE DEFAULT Country Mode = U.S. Country Mode = Belgium Country Mode = Britain Country Mode = Croatia Supports only the interfaces listed in the Country Mode feature description. Supports only the interfaces listed in the Country Mode feature description. Country Mode = Czechoslovakia Gryphon™ I GD4100 Country Mode Country Mode — continued ENTER/EXIT PROGRAMMING MODE Country Mode = Denmark Supports only the interfaces listed in the Country Mode feature description. Country

4.8 CHANGING DEFAULT SETTINGS Once your reader is setup, you can change the default parameters to meet your application needs. Refer to the preceding paragraphs for initial configuration in order to set the default values and select the interface for your application. In this manual, the configuration parameters are divided into logical groups making it easy to find the desired function based on its reference group. The first four groups are for Standard Interface parameter configuration: RS232

Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italy Gryphon™ Dx30/Mx30 Ed.: 09/2006 This manual refers to software version 3.1.0 and later ALL RIGHTS RESERVED Datalogic reserves the right to make modifications and improvements without prior notification. Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or consequential damages resulting from the use of this material. Product names mentioned herein are for identificatio

Barcode Label A label that carries a barcode and can be affixed to an article. Baud Rate A unit used to measure communications speed or data transfer rate. CDRH (Center for Devices and Radiological Health) This organization (a service of the Food and Drug Administration) is responsible for the safety regulations governing acceptable limitations on electronic radiation from laser devices. Datalogic devices are in compliance with the CDRH regulations. Code Positioning Variation in code placement t

During this process a series of brief “ticks” indicates that reading is proceeding correctly. ADVANCED FORMATTING NOT FOR PEN INTERFACES • CONCATENATION • • ADVANCEDFORMATTING • Please follow the setup procedure carefully for these parameters. NOTE The Advanced Formatting parameters may not be compatible with the IBM USB POS interface selection. NOTE 1. Read the Enter Configuration code ONCE, available at the top of page. 2. Read configuration codes precisely following the numbered procedure giv

EAN 8 IAAG1oI .. EAN 13 IAAH1rI .. UPC A IAAI1uI .. UPC E IAAJ1xI NO CHECK DIGIT TRANSMISSION EAN 8 IAAG0kI EAN 13 IAAH0nI UPC A IAAI0qI UPC E IAAJ0tI Enter Configuration Exit and Save Configuration I$+;I CODE SELECTION I$-?I CONVERSION OPTIONS UPC E to UPC A conversion IAAAAI UPC A to EAN 13 conversion IAACEI Enable only ISBN conversion IAP1nI Enable both ISBN and ISSN conversion IAP3tI UPC E to EAN 13 conversion IAABCI EAN 8 to EAN 13 conversion IAAD"I Enable only ISSN conversion IAP2qI Disabl

SERVICE, SUPPORT AND WARRANTY Datalogic provides several services as well as technical support through its website. Log on to and click on the links indicated for further information including: · Datalogic Services - Warranty Extensions and Maintenance Agreements · Downloads - Software Downloads, Manuals and Catalogues · Contact Us - Listing of Datalogic Subsidiaries and Quality Partners · Authorised Repair Centres SAFETY PRECAUTIONS For installation, use and maintenance it is not necessary to o

Consult Table 4-2 for more information regarding keyboard wedge interface types. The correct interface cable is included for the imager interface type you ordered. NOTE QuickScan® QS6500/QS6500 BT Table 4-2. Keyboard Wedge Interface Reference I/F Type PCs Supported A PC/XT w/Alternate Key Encoding B AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Encoding C PS/2 25 and 30 w/Alternate Key Encoding D PC/XT w/Standard Key Encoding E AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80

192 I 2 of 5 Check Character Calculation ................................................................................ 193 I 2 of 5 Check Character Transmission ............................................................................. 194 I 2 of 5 Minimum Reads ................................................................................................. 195 2 of 5 Decoding Level .................................................................................................... 196 I

Page references are also provided for feature descriptions and programming bar codes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features. Table 30. Standard Defaults Parameter Default Your Setting Page Number General Features Set Default Parameter Restore Defaults 21 Beeper Tone Medium 22 Beeper Volume High 22 Power Mode Continuous On 23 Scan Line Width Full Width 25 Laser On Time 3.0 Sec 25 Beep After Good Rea