Évaluations - 3, GPA: 5
(
)
)
|
Facilité d'utilisation
To avoid damaging plastic parts, do not use power tools for assembly. Wheel Nut (32)–2 1” Tek Screw (39)–4 Extension Leg Nut (46)–4 3/4” Screw (2)–6 1/4” Star Washer (96)–2 Leg/Handrail Bolt (93)–8 Silver Ground Screw (75)–1 Console Bolt (90)–2 Wheel Bolt (64)–2 Handrail Star Washer (95)–4 1. Make sure that the power cord is unplugged. With the help of a second person, carefully tip the treadmill onto its left side as shown. Partially fold the Frame (86) so the treadmill is more stable. Do not fully fold the treadmill until it is completely assembled. Orient an Extension Leg (63) so the Base Pad (61) is in the position shown, and insert the Extension Leg into the base of the Uprights (69). If necessary, use a rubber mallet to fully insert the Extension Leg. Next, hold two Extension Leg Nuts (46) in the bottom of the Extension Leg, and insert two Leg/Handrail Bolts (93) into the top of the Extension Leg. Firmly tighten the Leg/Handrail Bolts into the Extension Leg Nuts. Attach two Base Pads (57) to the base of the Uprights (69) with two 1” Tek Screws (39). 63 86 61 57 69 39 39 93 46 1 6 7 2. Attach a Wheel (66) to the base of the Uprights (69) with a Wheel Bolt (64) and a Wheel Nut (32) as shown. Do not overtighten the Wheel Bolt; the Wheel should turn freely. With the help of a second person, carefully tip the treadmill onto its other side. See assembly step 1 and attach the other Extension Leg (63) and Base Pads (57). Next, attach the other Wheel (66) as described above. With the help of a second person, carefully tip the treadmill so the base of the Uprights (69) is flat on the floor. 66 32 69 2 64 42 71 4. Have another person hold the Console Base (47) near the right Handrail (71). If there is a green ground wire on the Console Base, attach the end of the ground wire to the indicated small hole in the right Handrail with the Silver Ground Screw (75). Connect the Wire Harness (42) to the wire harness on the Console Base (47). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 75 47 Ground Wire 4 3. If there is a board between the Uprights (69), remove the board and the two bolts. Discard the board and the bolts. Remove the tie from the Wire Harness (42). Hold one of the Handrails (71) near the right Upright (69), and route the Wire Harness into the opening in the bottom of the Handrail and out of the indicated hole in the top. Set the Handrail (71) on the right Upright (69). Tighten two Leg/Handrail Bolts (93) with two Handrail Star Washers (95) into the Handrail and the right Upright. Make sure that the Wire Harness (42) is not pinched. Attach the other Handrail (71) to the left Upright (69) as described above. Note: There is not a wire harness on the left side. 69 69 42 93 95 71 95 93 71 3 42 5. Set the console assembly on the Handrails (71); insert the excess wiring down into the right Handrail. Attach the console assembly with four 3/4” Screws (2), two Console Bolts (90), and two 1/4” Star Washers (96) as shown. Make sure that no wires are pinched. Start all four Screws and both Console Bolts before tightening any of them. 90 2 90 96 96 2 71 71 5 Console Assembly 6. Attach the Latch Housing (29) to the left Upright (69) with 6 two 3/4” Screws (2). Make sure that the large hole in the Latch Housing is on the side shown. Do not overtighten the Screws. Remove the knob from the pin. Make sure that the collar and the spring are on the pin as shown. Insert the pin into the Latch Housing (29), and tighten the knob back onto the pin. 2 29 69 Knob Pin Collar Spring 7. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may be included. Keep the included allen wrenches in a secure place; the large allen wrench is used to adjust the walking belt (see page 18). To protect the floor or carpet, place a mat under the treadmill. 8 OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT Your treadmill features a walking belt coated with high- performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your home’s power. Voltage ...