Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
The CROSSWALK 365s treadmill combines advanced technology with innovative design to help you get the most from your exercise in the convenience of your home. And when you’re not exercising, the CROSSWALK 365s treadmill can be folded up, requiring less than half the floor space of other treadmills. For your benefit, read this manual carefully before using the treadmill. If you have questions after reading this manual, call 1-800-4-MY-HOME® (1-800-469-4663). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is 831.295030. The serial number can be found on a decal attached to the treadmill (see the front cover of this manual for the location). Before reading further, please review the drawing below and familiarize yourself with the labeled parts. Handrail Upright Storage Latch Key/Clip Reset/Off Circuit Breaker Walking Belt Cushioned Walking Platform for maximum exercise comfort Foot Rail Power Cord RIGHT SIDE Rear Roller Adjustment Bolts Console Bookrack Accessory Tray BACK Upper Body Arms 5 ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included allen wrenches and your own phillips screwdriver , rubber mallet , and adjustable wrench . For help identifying the assembly hardware, see the drawings below. If a part is not in the parts bag, first check to see if it has been pre-assembled. If a part is missing, call toll-free 1-888-533-1333. 1. Make sure that the power cord is unplugged. 3/4” Screw (2)–10 Wheel Nut (32)–2 2” Bolt (64)–2 Silver Ground Screw (75)–1 1” Tek Screw (39)–6 2 1/2” Bolt (37)–2 Washer (38)–4 1/2” Screw (48)–6 3 1/2” Bolt (45)–4 Star Washer (106)–4 With the help of another person, carefully raise the Uprights (69) to the vertical position. Insert one of the Extension Legs (63) into the treadmill as shown. (Note: It may be helpful to tip the Uprights as you insert the Extension Leg.) Make sure that the Base Pad (61) is under the Extension Leg. Insert the other Extension Leg (63) in the same way. 69 63 61 1 6 7 2. With the help of another person, carefully lower the Uprights (69) as shown. Note: It may be helpful to place one foot on one of the Extension Legs (63) as you tip the Uprights. Make sure that the Extension Legs remain in the Uprights. Attach each Extension Leg (63) with two 1” Tek Screws (39) and a Round Base Pad (57) as shown. Attach the lower Tek Screw, without the Round Base Pad, first. Attach two more Round Base Pads (57) to the base of the Uprights (69) with two 1” Tek Screws (39). Note: One replacement Round Base Pad may be included. If a Round Base Pad becomes worn and needs to be replaced, use the replacement Round Base Pad. Attach the two Wheels (66) with two 2” Bolts (64) and two Wheel Nuts (32) as shown. Do not overtighten the Bolts; the Wheels should be able to spin freely. With the help of another person, carefully raise the Uprights (69) to the vertical position. 39 69 63 39 57 63 57 57 39 66 64 32 69 64 66 32 57 39 3. With the help of a second person, tip the treadmill so the Base (not shown) is flat on the floor. Insert the tab on one of the Handrail Brackets (40) into the slot in the right Upright (69). Attach the Handrail Bracket with a 3/4” Screw (2). Attach the other Handrail Bracket to the left Upright (not shown) as described above. 40 2 69 Tab Slot 4. Identify the Right Handrail (72), which has a large hole in the left side. Feed the Upright Wire (42) into the hole in the bottom of the Right Handrail and out of the large hole in the side. Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole. Press a Handrail Cap (16) onto the lower end of the Right Handrail (5) as shown. Set the Right Handrail (72) on the right Upright (69), with the the lower end inserted into the Handrail Bracket (40). Attach the Right Handrail (72) with an Upright Bolt (37) in the upper end and a 3/4” Screw (2) in the lower end. Attach the Left Handrail (71) as described above. Note: There is not a wire harness on the left side. 42 Hole 72 37 37 71 16 2 2 69 40 Hole 2 3 4 5. Attach the Left Upper Body Arm (24) to the left Upright (69) with two 3 1/2” Bolts (45), two Washers (38), and two Star Washers (106) as shown. Make sure the Arm is on the indicated side of the crossbar. Attach the Right Upper Body Arm (not shown) to the other Upright (not shown) in the same way. Lower the Left Upper Body Arm (24) and the Right Upper...