Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
Description Qty. Order No. No. Description Qty. Order No. 59 Motor Hood 1 EVO3-59 89 Bushing 4 EVO3-89 60 #8 x 50mm Screw 2 EVO3-60 90 M10 x 60mm Bolt 2 EVO3-90 61 62 63 Side Rail (R & L) Deck End Cap - Left Running Belt 2 1 1 EVO3-61 EVO3-62 EVO3-63 91 92 93 Deck Frame Motor Hood Side Cover Right Motor Hood Side Cover Left 1 1 1 EVO3-91 EVO3-92 EVO3-93 64 Deck End Cap - Right 1 EVO3-64 94 Frame Side Cover - Right 1 EVO3-94 65 Rail Guide 8 EVO3-65 95 Frame Side Cover - Left 1 EVO3-95 66 M8 x 25mm Screw 10 EVO3-66 96 Plastic Clamp - Top 2 EVO3-96 67 Running Deck 1 EVO3-67 97 Plastic Clamp - Bottom 2 EVO3-97 68 Deck Cushion 10 EVO3-68 98 Bracket 2 EVO3-98 69 M10 x 35mm Bolt 9 EVO3-69 99 M8 x 19mm Allen Head Bolt 4 EVO3-99 70 M5 x 12mm Screw 2 EVO3-70 100 Rear Roller 1 EVO3-100 71 Clip 2 EVO3-71 101 Rear Roller Shaft 1 EVO3-101 72 Elevation Motor 1 EVO3-72 102 M8 x 43mm Bolt 2 EVO3-102 73 M10 x 63mm Hex Head Bolt 1 EVO3-73 103 Deck Wheel 2 EVO3-103 74 Washer 2 EVO3-74 104 Spring Washer 10 EVO3-104 75 Rubber Cushion 1 EVO3-75 105 M8 Nut 10 EVO3-105 76 77 M8 x 135mm Bolt M8 x 15 Screw 1 2 EVO3-76 EVO3-77 106 107 #8 x 35mm Screw Elevation Support Tube Cover -Left 3 1 EVO3-106 EVO3-107 78 Spring Washer 2 EVO3-78 108 M5 x 12 Screw 1 EVO3-108 79 8 x 16mm Washer 2 EVO3-79 80 M10 x 136mm Hex Head Bolt 1 EVO3-80 81 Motor Bracket 1 EVO3-81 82 Driving Motor 1 EVO3-82 83 Motor Drive Belt 1 EVO3-83 84 Front Roller with Fly Wheel 1 EVO3-84 85 86 Front Roller Shaft Elevation Support Tube Cover Right 1 1 EVO3-85 EVO3-86 87 Micro Switch 1 EVO3-87 88 M6 x 70mm Bolt 3 EVO3-88 Visit us at: EVO3 MOTORIZED TREADMILL Visit us at: 8 PARTS DIAGRAM A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY. EVO3 MOTORIZED TREADMILL Visit us at: 9 PARTS DIAGRAM A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY. EVO3 MOTORIZED TREADMILL Visit us at: 10 ASSEMBLY STEP 1: Remove your treadmill from the carton and place it on the floor in an open area as shown in FIG-1. First make sure to connect the wires. Then insert the Left and Right Uprights (28 and 29) into the Base Frame (48) and secure with M6 x 55mm Bolts (50), 6 x 13mm Washers (56) and M8 x 19mm Allen Head Bolts (32). EVO3 MOTORIZED TREADMILL Visit us at: 11 ASSEMBLY STEP 2: Rotate the Console Support Tube (5) up to the correct position as shown and secure in place using M5 x 10mm Screw (9). EVO3 MOTORIZED TREADMILL Visit us at: 12 ASSEMBLY STEP 3: Rotate the Computer (1) up to the correct position as shown and secure in place using M6 x 15mm Console Screws (8). EVO3 MOTORIZED TREADMILL Visit us at: 13 ASSEMBLY STEP 4: NOTE: If you have the Optional Smooth Music Package follow these instructions before attaching the Console Tray (39). Run the Cd Player Wires from the back of the Computer (1) first through the small hole on the Console Tray (39), then through the tabs on the back of the Console Tray (39) and finally through the small hole on the side of the Computer (1) as shown in FIG-2. Insert the Console Tray (39) into the back of the Computer (1) and secure with M5 x 12mm Screw (108). EVO3 MOTORIZED TREADMILL Visit us at: 14 ASSEMBLY STEP 5: Attach the Cross Brace (27) to the Left Upright (28) and Right Upright (29) using Metal Caps (26) and M8 x 76mm Allen Head Bolts (25). EVO3 MOTORIZED TREADMILL Visit us at: 15 ASSEMBLY STEP 6: Unscrew M8 x 25mm Screw (49). Insert the Console Support Tube (40) into the Cross Brace (27) and secure with M8 x 25mm Allen Head Bolt (49). Do not fully tighten until later. EVO3 MOTORIZED TREADMILL Visit us at: 16 ASSEMBLY STEP 7: Rotate the Console Support Tube (40) and slide it into the hole underneath the Console Tray (39). EVO3 MOTORIZED TREADMILL Visit us at: 17 ASSEMBLY STEP 8: Attach the Upright Plastic Shrouds Left #1 and Left #2 (41 and 42) to the Left Upright (28) and secure using M8 x 19mm Screws (16) and M8 x 25mm Screws (17). Repeat this procedure with Upright Plastic Shrouds Right #1 and Right #2 (43 and 44) on the Right Upright (29) and secure with M8 x 19mm Screws (16) and M8 x 25mm Screws (17). EVO3 MOTORIZED TREADMILL Visit us at: 18 ASSEMBLY STEP 9: Fully tighten M8 x 15mm Bolt (21), M8 x 76mm Allen Head Bolt (25) and M8 x 25mm Screw (17). EVO3 MOTORIZED TREADMILL Visit us at: 19 ASSEMBLY STEP 10: Connect the Motion Control Sensor and Hand Pulse Sensor Wires. Then, attach the Left and Right Handlebars (14 and 15) to the Left and Right Uprights (28 and 29) and secure using M8 x 10mm Allen Head Bolts (23). EVO3 MOTORIZED TREADMILL Visit us at: 20 ASSEMBLY STEP 11: Insert the Handlebar Rear End Cap – Left #1 (10) and Handlebar Rear End Cap – Left #2 (11) over the Left Upright (28) and secure in place using M8 x 25mm Screws (17) and M8 x ...