Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
The following Parts Identification Listing and the step by step installation procedures have been assembled to make the set-up of your aerobic trainer as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Lifecycle exercise bike… S A F E T Y F I R S T ! . DO NOT locate the Lifecycle 9100R aerobic trainer outdoors, near swimming pools, or in areas of high humidity. . DO NOT operate your Lifecycle 9100R aerobic trainer if it has been dropped, damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services at the number on the back page of this Installation Instruction Guide. . DO NOT locate the Lifecycle 9100R aerobic trainer any closer than 30 inches ( 76 cm ) to a television set. . DO keep the area around your Lifecycle 9100R aerobic trainer clear of any obstructions, including walls and furniture. . DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the number listed on the back page of this Installation Instruction Guide. Save the shipping cartons in case of return. . DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use. TOOLS REQUIRED FOR ASSEMBLY... Phillips screwdriver, 1/2” wrench, 5/32” hex key wrench PARTS DESCRIPTION 1 Seat Back Screw 0017-00101-1131 Qty. 4 2 Seat Back Washer 0017-00104-0253 Qty. 4 3 Handlebar Bolt 0017-00101-0986 Qty. 2 4 Console Screw 0017-00101-1104 Qty. 4 5 Seat Back 0K19-01078-0000 Qty. 1 6 Collar 0K19-01125-0000 Qty. 1 7 Handlebar Assembly AK19-00035-0000 Qty. 1 8 Display Console AK19-00114-0001 Qty. 1 9 9V Alkaline Battery 0017-00003-0573 Qty. 1 10 11 12 Step 1 Align the four holes in the SEAT BACK (#5) with those in the SEAT BACK POSTS. Insert the four SCREWS (#1) and WASHERS (#2) through the backside of the SEAT BACK POSTS and into the SEAT BACK. Tighten the four SCREWS with a hex key wrench. NOTE: BE CAREFUL NOT TO OVER-TIGHTEN THE SCREWS. Step 2 Unfold the CONSOLE WIRE HARNESS from the POST extending from the FRAME. Step 3 Slide the COLLAR (#6) onto the HANDLEBAR ASSEMBLY (#7) with the angled side of the COLLAR facing toward the HANDLEBAR. Step 4 While holding the HANDLEBAR ASSEMBLY (with the COLLAR in place) in one hand, feed the WIRE HARNESS at the top of the FRAME POST through the bottom of the HANDLEBAR ASSEMBLY COLUMN, as shown, with your other hand. Continue pushing the WIRE HARNESS until the CONNECTOR at the end of the WIRE HARNESS exits through the opening at the top of the COLUMN. Gently pull the WIRE HARNESS to remove the slack. Step 5 Position the HANDLEBAR ASSEMBLY so that the HANDLEBAR is facing the user and slide the HANDLEBAR ASSEMBLY into the FRAME POST while being careful not to pinch the WIRES in the process. Align the holes in the bottom of the HANDLEBAR ASSEMBLY with those in the FRAME POST. (Both the HANDLEBAR ASSEMBLY and the FRAME POST are keyed to ease the alignment and positioning). Install the two HANDLEBAR BOLTS (#3) to secure it into position. NOTE: BE VERY CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES. TIGHTEN THE BOLTS SECURELY. Step 6 There is a large hole in the rear of the DISPLAY CONSOLE (#8) through which you can see a 16-PIN CONNECTOR. This corresponds to the matching WIRE HARNESS CONNECTOR protruding from the top of the HANDLEBAR ASSEMBLY. Properly align the LOCKING TABS of the 16-PIN CONNECTORS and plug them together until they SNAP into place. Step 7 Carefully feed the wire back into the top of the HANDLEBAR ASSEMBLY and attach the DISPLAY CONSOLE to the HANDLEBAR ASSEMBLY using the four CONSOLE SCREWS (#4) and a phillips screwdriver. Tighten the four SCREWS in a criss-cross pattern. NOTE: BE CAREFUL NOT TO OVERTIGHTEN THE SCREWS. Step 8 To install the 9-VOLT ALKALINE BATTERY (#9) found in the parts bag use a Phillips screwdriver to remove the screw from the back door. Gently pull the BATTERY WIRES from the back of the DISPLAY CONSOLE and connect them to the 9-VOLT ALKALINE BATTERY. Carefully, tuck the BATTERY WIRES back into the DISPLAY CONSOLE and set the BATTERY in place. Re-install the BATTERY DOOR by inserting the bottom tab of the BATTERY DOOR into the corresponding slot in the DISPLAY CONSOLE. Push the DOOR into place and tighten the screw with a Phillips screwdriver. NOTE: ONLY USE AN ALKALINE TYPE BATTERY. USE OF ANY OTHER TYPE BATTERY MAY RESULT IN A MALFUNCTION OR DAMAGE. CAUTION!: BE CAREFUL NOT TO OVER TIGHTEN THE SCREW Step 9 Slide the COLLAR (#6) down until it completely covers the HANDLEBAR ASSEMBLY HARDWARE and the POST extending up from the FRAME. Secure the COLLAR by “pinching” in the sides and pushing down firmly. The COLLAR will lock into place. Step 10 After placing the Lifecycle in the intended location for use, check the stability of ...