Évaluations - 4, GPA: 3.3
(
)
)
|
Facilité d'utilisation
1 12. 1/2 ID X 5/8 IN SPACER..................................................... ..............................................1 13. SPRING PIN ASSEMBLY................................................... .............................................. 1 1A 1/9 TNTD CAPNUT ............................................. .............................................. 1 15. 3X2 IN INSERT GUIDE.................................................... ..............................................2 1 A V 9 TN KMD CAP ....................................... ..............................................3 ID. 17. 7/16 ID X 4 IN VINYL CAP................................................ ..............................................1 WELDMENTS/PARTS: ITEM NAME/DESCRIPTION QTY 1. REAR UPRIGHT WELDMENT...............................(6651703).....................................1 2. BENCH FRAME WELDMENT................................(6652103).....................................1 3 ADJ SLEEVE WELDMENT.....................................(6652803)...................:.................1 4 BACK PAD ANGLE WELDMENT LEFT...............(6624202).....................................1 5 BACK PAID ANGLE WELDMENT RIGHT ............(6624302).....................................1 6. 1/2 X 2 X15-1/2 IN PLATE .......................................(6651602).....................................2 7. SEAT PAD....................................(66S3SXX)'..................................... 1 8. BACK PAD...............................................................(66529X3Q.....................................1 NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE 130LT. 1/2 I 6 1/2 1/2 0 1/2 1/2 1/2 Part #6653501 2 Revision: 11/26/96 965101 FLAT & INCLINE BENCH ASSEMBLY INSTRUCTIONS THANK YOU FOR PURCHASING THE MSWi FIAT & INCUSE HENCH. PLEASE SAVE TKI'SE ASSEMBLY INSTRUCTIONS FOR YOUR PERSONAL HEKEREN( E, AN» AUDITION \h SERVICE INFORMATION* ***T IMPORTANT*** * TTTF, M&m FIAT & mCUNE BENCH MUST BE ASSEMBLED ON A FLAT* LEVEL SIIJIFACE TO ASSURE ITS PROPEl FUNCTION', ♦ IP VOU EXPERIENCE A> V PROBLEM WI Ul THE ASS EM BLY OF THIS PRODUCT. PI .EASE CONTACT YOUR DEALE 1 OR YOLR PARA BODY CISTC, MER SERVICE REF RESENT ATI VE AT: . TOOLS REQUIRED: 1UTCHET, 3-4 SOCKET and WRENCH, 9fu SOCKET .ml WRENCH. ami RUBBER MALLET or HAMMER Slide one (1) 7/16 ID X 4 IN VINYL CAP onto the 6-1/8 X 3-7/8 IN U-PIN and proceed to assemble it to the BENCH FFAME WELDMENT as shown on drawing. Insert two (2) 3 X 2 INSERT GUIDES into each end of the APJ SLEEVE WELDMENT as shown on drawing. (NOTE: MAKE SURE THE INSERT GUIDES SHAP INTO THE HOLES OF THE WELDMENT),. SECURELY assemble the SPRING PIN ASSEMBLY to the ADJ SLEEVE WELDMENT as shown in (DETAIL A). Pull back the SPRING PIN on the ADJ SLEEVE WELDMENT and slide it over the end of the BENCH FRAME WELDMENT as shown on drawing. Slide WELDMENT up to the first adjustment hole underneath. Insert three (3)3 X 2 IN END CAPS into the ends of the REAR UPRIGHT WELDMENT as shown on drawing. SECURELY as semble the REAR UPRIGHT WELDMENT to the BENCH FRAME WELDMENT as shown on drawing. Assemble the LEFT and RIGHT BACK PAD ANGLE WELDMENTS, along with two (2) HINGE TABS to the BENCH FRAME WELDMENT as shown on drawing. (NOTE: TIGHTEN CONNECTION ENOUGH TO REMOVE THE PLAY YET ALLOWING THE PARTS TO . ROTATE FREELY). Assemble two (2) 1/2 X 2 X 15-1/2 IN PLATES to the inside of the LEFT and RIGHT BACK PAD ANGLE WEL DMENTS as shown on drawing. (NOTE: TIGHTEN CONNECTION ENO UGH TO REMOVE THE PLAY YET ALLOWING THE PARTS TO ROTATE FREELY). Rotate the LEFT and RIGHT BACK PAD ANGLE WELDMENTS up and assemble the 1/2 X 2 X 151/2 IN PLATES to the ADJ SLEEVE WELDMENT as shown on drawing. (NOTE: DO NOT OVER TIGHTEN TBIS CONNECTION). Part #6653501 3 Revision: 11/26/96 965101 FLAT & INCLINE BENCH ASSEMBLY INSTRUCTIONS 9. SECURELY assemble the BACK PAD to the LEFT and RIGHT BACK PAD ANGLE WELDMENTS as shown on drawing. 10. SECURELY assemble the SEAT PAD to the HINGE TABS on the BENCH FRAME WELDMENT as shown on drawing. Part #6653501 4 Revision: 11/26/96 DASH NO DESCRIPTION 01 AS SHOWN 3 X 2 END CAP (3) REAR UPRIGHT WELDMENT (6651703) 3 X 2 IN INSERT GUIDE (2) ADJ SLEEVE WELDMENT (6652803) 1/2 X 2 X 15-1/2 IN PLATE (6651602) 1/2 X 6-1/2 IN BOLT 1/2 IN LOCK NUT (2) BACK PAD ANGLE WELDMENT LEFT (6624202) 3/8 X 1 IN BOLT (4) 3/8 IN WASHER (4) 1/2 IN WASHER (4) 1/2 X 9-1/2 IN BOLT HINGE TAB (2) 3/8 IN WASHER (2) 3/8 X 1 IN BOLT (2) © 6-1/8 X 3-7/8 U PIN REVISIONS REV DESCRIPTION CHG NO APP'D DATE c WAS 4-3/8 ôôo i D ifr\ "fob 1/2 X 1-1/4 IN BOLT (2) 1/2 X IN WASHER (2) 1/2 IN LOCK NUT 1/2 X 3 IN BOLT (2) BACK PAD (66529XX) 1/2 IN LOW HT LOCK NUT (2) BACK PAD ANGEL RIGHT (6624302) SEAT PAD (66353XX) 1/2 IN LOW HT LOCK NUT 1/2 IN ID CAPNUT 1/2 ID X 5/8 IN SPACER 7/16 ID X 4 IN VINYL CAP BENCH FRAME WELDMENT (6652103) TOLERANCES (EXCEPT AS NOTED) PARABODY, INC. RAMSEY, M...