Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
4 5 6 WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 5. P/N 21495407 08/05 10 6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7 4 8 6 5 7. Insert pole assembly into tank assembly as shown. 6 WARNING! 7 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR 8 PROPERTY DAMAGE. IMPORTANT!: DO NOT OVER TIGHTEN 8. Carefully place unit on its side. Secure pole bottom (6) to tank with anchor strap (52), washers (9 & 13) and nut (10) as shown. Upright unit. NOTE: 69 13 Keep unnecessary pressure DO NOT OVER TIGHTEN IMPORTANT!: off of the pole assembly when in this position. Two people recommended for this procedure. 1 52 10 11 08/05 P/N 21495407 1 11 11 12 13 6 14 13 Secure strut tubes (11) to bottom pole section (6) as shown. TIGHTEN BOLT (14) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 9. 1 11 11 12 13 6 14 13 Secure strut tubes (11) to bottom pole section (6) as shown. TIGHTEN BOLT (14) IN LOCK NUT (12) UNTIL FLUSH (EVEN) WITH LOCK NUT’S OUTER EDGE. WARNING! 9. 12P/N 21495407 08/05 15 16 11 1 13 13 4 16 37 18 18 16 17 Carefully place unit in the side position and secure strut (11) to tank (1) as shown. Completely tighten. Repeat for opposite side. Upright unit. Install pole mount bracket (17) and reinforcement bracket (37) with carriage bolts (18) as shown. Tighten flange nuts (16) completely. Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this procedure. NOTE: 10. 11. 1 FRONT SIDE 13 08/05 P/N 21495407 19 21 21 19 20 19 20 19 17 22 22 23 23 Attach spacers (22, 23) to pole mount bracket (17) with bolts (21), washers (19), and nuts (20) as shown. Tighten just until washers (19) stop moving. IMPORTANT!: 17 16 26 24 24 27 25 FIG. A Assemble lanyard (27) to locking pin (26) as shown (FIG A). Attach covers (24) onto pole mount bracket (17) with carriage bolt (25) and nut (16) as shown. Loop end of pin lanyard (27) over carriage bolt (25) as it passes through the pole mount bracket (17) during this assembly. IMPORTANT!: 25 27 26 12. 13. Apply logo and height indicator labels (29) to adjustment rod (28) as shown. Attach handle 14. parts (32, 33) to adjustment rod with screw (31), carriage bolts (30), and flange nuts (16) as shown. 30 29 16 28 Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. IMPORTANT!: 31 30 16 32 33 15. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (26). 28 26 P/N 21495407 08/05 14 Attach backboard support brackets (34) to the backboard frame using bolts (21), 16. spacers (36), and nuts (20) as shown. 36 36 21 21 20 20 34 15 08/05 P/N 21495407 Attach rim to board as shown. For spring loaded rim assembly, refer to instructions included with rim hardware. Assemble lower elevator tubes (40) as shown. DO NOT 17. overtighten. 47 42 4041 40 55 35 35 34 39 16 IMPORTANT!: It is necessary for all parts to be installed for this mechanism to work safely and properly. IMPORTANT!: Refer to instructions included with board and rim hardware for backboard and rim assembly. P/N 21495407 08/05 16 Assemble upper elevator tubes (43) to backboard brackets (34). DO NOT overtighten. 18. 43 43 47 35 34 39 35 40 SAWHORSE OR SUPPORT TABLE Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (46). USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! IMPORTANT!: DO NOT OVER TIGHTEN 39 48 40 46 40 40 4 45 45 47 38 38 NOTE: STEP 5 COMPLETED ASSEMBLY: 19. 17 08/05 P/N 21495407 Install upper elevator tubes (43) to triangle plates (45) using bolt (47), spacers (38), and nut (39) as shown. 20. 47 3944 44 28 Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. NOTE: IMPORTANT!: DO NOT OVER TIGHTEN 40 47 38 40 39 43 38 45 43 21. Install handle assembly to lower elevator tubes (40) using bolt (47), spacers (44), and nut (39) as shown. 40 40 P/N 21495407 08/05 18 41 39 47 43 43 Insert bolt (47) through left side upper elevator tube (43), then stretch spring (41) onto bolt (47). Insert bolt (47) through right side upper elevator tube (43) and secure with nut (39). USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! 22. 43 41 39 47 43 43 Insert bolt (47) through left side upper elevator tube (43), then stretch spring (41) onto bolt (47). Insert bolt (47) through right side upper elevator tube (43) and secure with nut (39). USE EYE PROTECTION WHEN INSTALLING SPRINGS. WARNING! 22. 43 08/05 P/N 2149540719 53 49 52 /115 Liters) or sand (approx. 255 lbs./113 kg) and snap cap (49) in place. DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! ADD TWO GALLONS (7.6 ...