Évaluations - 5, GPA: 4.4
(
)
)
|
Facilité d'utilisation
• Adult supervision is recommended when adjusting height. Most injuries are caused by misuse and/or not following instructions. Use caution when using this system. 200439 11/00 1 3 2 MOVING SYSTEM 1. While holding pole, rotate basketball system forward until wheels engage with ground. 2. Move basketball system to desired location. 3. Carefully rotate basketball system upright. 4. Reattach ground restraint and check system for stability. HEIGHT ADJUSTMENT A WARNING Backboard may rotate during height adjustment. B WARNING Do not adjust height of system in upright position. System must be in down position to adjust Rest unit on support table. Remove adjustment knobs (A) and carriage bolts (B) to extend or retract backboard and rim. Height adjustment from 7 1/2' to 10'. 15 3 10/03 P/N 214994C NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. 4 P/N 214994C 10/03 Get to know the basic parts of your basketball system..... STRUTS BACKBOARD FRONT RIM WHEEL CARRIAGE ASSEMBLY BASE POLE 5 10/03 P/N 214994C PARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 206645 Tank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 900060 Top Pole Section 1 908480 Middle Pole Section with Label 6 1 908490 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 202822 Eye Bolt, 3/8 x 16 x 3-3/4 Long 9 1 200627 Wheel Bracket 1 203063 Lock Nut, Nylon Insert, 3/8-16 11 1 201625 Bolt, Hex Head, 5/16-18 x 3-3/4 12 6 203218 Washer, 5/16 Flat 13 2 906206 Tank Strut 14 1 203220 Lock Nut, 5/16-18 1 200439 Label, Moving System and Height Adjust. 16 2 203156 Bolt, Hex Head, 5/16-18 x 1 Long 17 6 203100 Nut, Hex Flange 5/16-18 18 1 Rim 19 12 201219 SmartClip, Net Holder 2 900057 Backboard Mounting Bracket 21 4 203309 Washer, 1 O.D. 22 4 203113 Bolt, Hex Flange, 5/16-18 x 2-1/2 Long 23 2 203231 Bolt, Carriage 5/16-18 x 3-1/2 24 2 203435 Knob, Plastic, 1-3/4 Diameter 1 Net 26 1 206219 Cap 27 1 203124 Tie Down Stake 28 2 201651 Spacer, Wheel Axle 29 1 201568 T-Strap 1 203617 Tank Cap * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. 6 P/N 214994C 10/03 HARDWARE IDENTIFIER (BOLTS & RODS) Item #16 (2) Item #22 (4) Item #23 (2)Item #8 (1) Item #11 (1) Item #7 (1) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #14 (1) Item #12 (6) Item #10 (1) Item #17 (6) Item #21 (4) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #19 (12) Item #28 (2) 7 10/03 P/N 214994C SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) 9/16” and 1/2” 9/16” and 1/2” AND/OR Item #14 (1) Item #12 (6) Item #10 (1) Item #16 (2) Item #17 (6) Item #21 (4) Item #28 (2) Item #8 (1) Item #11 (1) Item #7 (1) 8 P/N 214994C 10/03 1. 1 Remove contents from tank Remove contents from tank 2. Correctly identify each pole section and mark indicated distance from ends with tape (not supplied) as shown. TOP 4 TAPE (Not Supplied) MIDDLE 5 5” (13 cm) BOTTOM 6 5” (13 cm) 3. IMPORTANT! Center the alignment slot of middle pole section (5) in the lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle section of pole (5) into top section of pole (4) using wood scrap as shown until they no longer move toward taped reference mark. WOOD SCRAP (NOT SUPPLIED) 5 4 POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 9 10/03 P/N 214994C NOTE: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. 4 5 6 WOOD SCRAP 4. IMPORTANT! Center the alignment slot of lower pole section (6) in the lower hole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using wood scrap as shown until they no longer move toward taped reference mark. 6 5 5. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 8 7 6 8 7 46 5 10 P/N 214994C 10/03 10 6 7 8 6. 28 Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown. A deep socket is recommended. 11 13 1 14 13 12 127. Secure tank struts (13) to pole. Rotate non-secured ends of tank struts (13) outward to mounting holes in tank as shown. IMPORTANT!...