Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
- Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away. CAUTION 1) For general ventilation use only. Do not use to exhaust hazardous or explosive materials and vapors. 2) To reduce the risk of fire, use only metal ductwork. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) to prevent back drafting. 3) Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and code authorities. 4) Activating any switch on may cause ignition or an explosion. 5) Due to the size and weight of this hood, two people installation is recommended. ELECTRICAL SHOCK HAZARD – Can result in serious injury or death. Disconnect appliance from electric power before servicing. If equipped, the fluorescent light bulb contains small amounts of mercury, which must be recycled or disposed of according to Local, State, and FederalCodes. 3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) RANGE HOOD BOX KOBE Range Hood – 1 Warranty Registration Card –1 Instructions Manual – 1 Baffle Filter -2 (30”, 36”, 42”) - 3 (48”) Stainless Steel Spacer - 1 (30”) - 3 (36”) - 3 (42”) - 2 (48”) Oil Tunnel – 1 Ducting Transition – 1 Screw Package for Transition – 1 Hood-Mounting Bracket-2 Screw Package for Hood-Mounting Bracket–1 . . . . . . . . . . ORIGINAL KIT (Sold Separately) Option Of: Model No. CH0030DC-12 for 30'' hood KOBE Duct Cover – 1 Screw Package for Duct Cover - 1 Hood-Mounting Bracket-2 Model No. CH0036DC-12 for 36'' hood KOBE Duct Cover – 1 Screw Package for Duct Cover - 1 Hood-Mounting Bracket-2 Model No. CH0042DC-12 for 42'' hood KOBE Duct Cover – 1 Screw Package for Duct Cover - 1 Hood-Mounting Bracket-2 Model No. CH0048DC-12 for 48'' hood KOBE Duct Cover – 1 Screw Package for Duct Cover - 1 Hood-Mounting Bracket-2 3/16" X 3/8" (8 pc) - FOR MORE INFORMATION, PLEASE VISIT OUR WEBSITE OR CONTACT KOBE RANGE HOODS AT (626)-775-8880. 4 INSTALLATION PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING Calculation before Installation Calculate the length of the installation, before installing the hood. (All calculation is measure in inches.) - FOR UNDER THE CABINET TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Preferred Height of Counter Top to Hood Bottom (Recommended 27” to 30”) D = Height of Hood E = Height of the Cabinet - FOR WALL MOUNT (WITH OPTIONAL DUCT COVER) TABLE 2 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Preferred Height of Counter Top to Hood Bottom (Recommended 27” to 30”) [(A – B] – (D + E)] D = Height of Hood E = Height of Duct Cover 5 SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES; PLEASE WEAR PROTECTIVE GLOVES IF IT IS NECESSARY TO REMOVE ANY PARTS FOR INSTALLING, CLEANING OR SERVICING. NOTE: BE CAREFUL WHEN USING ELECTRICAL SCREWDRIVER, DAMAGE TO THE HOOD MAY OCCUR. Installation Contents UNDER THE CABINET INSTALLATION ............................................................................................... 7. WALL MOUNT INSTALLATION............................................................................................................. 9. 6 UNDER THE CABINET INSTALLATION Preparation before Installation Figure 1 NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. . Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. . A straight, short venting run will allow the hood to perform more efficiently. . Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. . Temporarily wire the hood to test for proper Figure 2 operation before installing. . Important: Peel protective film off the hood (if any). . For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not included) on each side. Refer to Figure 2. . Measure and create access opening for electrical wires under the cabinet. Hood Installation CAUTION: If required to move the cooking range to install the hood, turn off the power on an electric range at the main electrical box. Figure 3 SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. 1. Puncture the knockout holes on the hood as shown in Figure 3. 2. Attach ducting transition to hood exhaust with ten (3/16” x 3/8”) screws (included). Shown in Figure 4. 3. Using references on Table 1 and measurements on page 16-17 to center the hood in place beneath the cabinet and flush with the front of the cabinet. 4. Draw electrical wires through cabinet access Figure 4 opening. 5. From the bottom of the hood, place screw (not provided) into the exact center of each knockout hole. Make sure all screws are in place before tightening screws. CAUTION: MAKE SUR...
Ce manuel est également adapté pour les modèles :Formateurs - CH0330SQB (2.54 mb)
Formateurs - CH0342SQB (2.54 mb)
Formateurs - CH0348SQB (2.54 mb)