Évaluations - , GPA:
(
)
)
Fabricant : Precor
Taille : 3.74 mb
Nom Fichier : C-Line_Abdominal_Guide_Manual_Assembly_English.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Figure 9: Front shroud attachment 3. Slide the bottom edge of the front shroud into the space between the exercise station and the weight stack frame. 4. When the plastic hooks on the front shroud line up with the large square holes at the top of the weight stack frame, place the hooks into the holes. A second set of hooks halfway up the shroud fits into holes in the weight tower frame. If necessary, lift the front shroud until the hooks drop into their holes in the weight tower frame and lower shroud until the hooks are supporting the shroud on the frame. Note: When attaching screws, take care to avoid cross-threading. 5. Attach the bottom edge of the front shroud using: Four ...”- 20 buttonhead screws 6. Leave the screws slightly loose until all four of them are attached and the front shroud is positioned correctly, and then tighten them using the ...” hex key until snug. Note: Two of the four screw locations are inside the sockets at the lower corners of the front shroud. The other two are between them along the bottom edge of the shroud. Figure 10: Screw locations on the front shroud 7. Replace the weight selection pin in the weight stack. To Install the Covers Below the Front Shroud: Note: Do not tighten all fasteners for the bottom covers until all shroud parts are in place. 1. Locate the two bottom corner covers (one left, one right). Select the cover that corresponds to the pulley location. Tilt the cover down and slide the tab under the front shroud. Secure the lower corner cover using: One ...”- 20 buttonhead screw Note: As you attempt to attach the corner cover, you might encounter resistance from the pulley cover. Tilting the corner cover down and applying pressure will ensure that it is properly positioned. Tighten screw using a ...” hex key until snug. Figure 11: Installation of corner cover 2. Fasten the cover plate to the second lower corner cover using: Two #8 self-tapping screws Figure 12: Attachment of cover plate to the lower corner cover 3. Slide the retaining feature on the second lower corner cover under the front shroud on the remaining corner and attach the second lower corner cover using: One ...”- 20 buttonhead screw Tighten screw using a ...” hex key until snug. Figure 13: Tab slides under the front shroud 4. Attach the lower middle cover by squeezing and snapping its tabs into the slots in the frame. 5. Firmly press the tabs located at the top of the lower middle cover under the bottom edge of the front shroud. Figure 14: Lower middle cover attachment 6. Tighten all bottom shroud fasteners until snug. To Install the Upper and Lower Back Shroud: 1. Position the lower back so that its tabbed end is at the top. Note: Do not tighten any of the screws until all four screws are attached. 2. Line up the two screw holes near the upper corners of the lower back with the corresponding holes in the weight stack frame. 3. Attach the upper corners of the lower back to the weight stack frame using: Two ...”- 20 buttonhead screws 4. Attach the lower corners of the lower back using: Two ...”- 20 buttonhead screws 5. Tighten all four screws using a ...” hex key until snug. 6. Position the upper back so that its tabbed end is at the bottom and insert its tabs between the tabs at the upper edge of the lower back. Figure 15: Lower back shroud attachment 7. Insert the tabs in the top corners of the upper back into the square holes at the top of the weight stack frame and push the corners in until the tabs lock into place. Figure 16: Upper back shroud attachment To Install the Top Cover: 1. Insert the tabs on the top cover into the matching slots in the shroud assembly. 2. Push down on the top cover until its tabs lock into place. Figure 17: Shroud top cover attachment To Remove the Nameplate Protective Film: 1. Locate the Precor nameplates on the front and back sides of the assembled shroud. 2. Peel the protective film off each Precor nameplate. Disassemble the Equipment This unit arrives fully assembled except for the shrouds and the bottle holder/accessory tray. In some cases, you may need to disassemble the unit before you move it. WARNING: You will need assistance to disassemble this unit. The weight tower is unstable when disconnected from the exercise station. Make sure the weight tower is supported safely during disassembly. Do not attempt disassembly by yourself. To Detach the Cable: 1. Loosen the locking jam nut and unscrew the bolt in the center of the top weight cap using a ..” open-end wrench. 2. Route the cable through the top of the weight tower and down to the lower 6” pulley. 3. Remove the shoulder bolt from the 6” pulley using a ..” hex key. 4. Unfasten the 6” pulley and unthread the cable. Note: Remove the pulley cable from the weight stack and keep it attached to the exercise station. To Separate the Weight Tower from the Exercise Station: Note: The exercise station is attached to the weight tower at a side location and a bottom location. 1. Locate the side area where the exercise...