Évaluations - , GPA: ( )

Instructions Horizon Fitness, Modèle CLUB SERIES CSE4.6

Fabricant : Horizon Fitness
Taille : 2.88 mb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

* Also enter this serial number on your Warranty Card. .......... .......... ............ ........ WARNING IMPORTANT PRECAUTIONS INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES TOOLS INCLUDED PARTS INCLUDED c 5mm Allen Wrench c 6mm Allen Wrench c Phillips Screw Driver c 13/15mm Flat Wrench c 1 Console c 1 Console Mast c 1 Front Stabilizer Tube c 2 Upper Handlebars c 2 Lower Handlebars c 2 Lower Link Arms c 2 Pivoting Foot Pads c 2 Top Side Covers c 1 HORIZON FITNESS 12-volt Power Supply CONSOLE (CSE4.6 shown) UPPER HANDLEBAR MAIN FRAME LOWER HANDLEBAR LOWER LINK ARM FRONT STABILIZER TUBE GRIP PULSE CONSOLE MAST ACCESSORY TRAY PIVOTING FOOT PAD PEDAL ARM c 6 Hardware Bags c 1 Accessory Tray c 3 Stabilizer Covers c 2 Handlebar Covers c 2 Elbow Covers HAND GRIPS (CSE4.6 only) If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual. For a complete exploded diagram, visit us at TOP COVERS 2 4 6 8 10 12 18 20 14 16 S TOP/PAUSE HOLD TO RESET STA RT QUICK START SPEED/LEVEL CAL/PULSE DISTANCE TIME DATE CLOCK BEFORE YOU BEGIN ASSEMBLY IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY .......................................... ................ .................... .................... .................... ASSEMBLY STEP 1 A) Open HARDWARE BAG FOR STEP 1. B) Attach the FRONT STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A), 2 WASHERS (B) and 2 WASHERS (C). ................ .......... ............ .................................. .......... ............ .............................. .......... ............ HARDWARE BAG FOR STEP 1 CONTENTS : INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES ASSEMBLY STEP 2 MAIN FRAME CONSOLE WIRES BOLT (A) CONSOLE MAST SPRING WASHER (B) FLAT WASHER (C) CONSOLE MAST GROMMET A) Open HARDWARE BAG FOR STEP 2. B) Carefully pull the CONSOLE WIRES through the CONSOLE MAST using the twist tie located inside the CONSOLE MAST. C) Attach the CONSOLE MAST to the MAIN FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C). BOLT (A) 20 mm Qty: 4 SPRING WASHER (B) 18 mm Qty: 4 FLAT WASHER (C) 20 mm Qty: 4 SCREW (K) 10 mm Qty: 2 HARDWARE BAG FOR STEP 2 CONTENTS : BEFORE YOU BEGIN ASSEMBLY IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY MAIN FRAME CONSOLE MAST GROMMET SCREWS (K) TOP SIDE COVERS ACCESSORY TRAY D) Insert the left TOP SIDE COVER, followed by the right TOP SIDE COVER and snap them together. E) Insert ACCESSORY TRAY and secure it using 2 SCREWS (K) as shown. F) Slide CONSOLE MAST GROMMET down to seal the console mast hole. ASSEMBLY STEP 2 B 10 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES ASSEMBLY STEP 3 A) Open HARDWARE BAG FOR STEP 3. B) Attach REAR STABILIZER COVER using 2 BOLT (L). C) Attach FRONT STABILIZER COVERS using 4 SCREWS (M). BOLT (L) 20 mm Qty: 2 SCREW (M) 10 mm Qty: 4 HARDWARE BAG FOR STEP 3 CONTENTS : REAR STABILIZER COVER FRONT STABILIZER COVER BOLTS (L) SCREWS (M) BEFORE YOU BEGIN ASSEMBLY 11 IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY ASSEMBLY STEP 4 CONSOLE MAST LOWER HANDLEBAR PRE-ATTACHED BOLT & WASHER UPPER HANDLEBAR PRE-ATTACHED SET SCREWS NOTCH TAB NOTE: There is NO hardware bag for this step. All hardware is pre-installed. A) Remove PRE-ATTACHED BOLT & WASHERS from CONSOLE MAST. B) Slide LOWER HANDLEBARS onto CONSOLE MAST and attach by re-inserting PRE-ATTACHED BOLT & WASHERS. C) Slide UPPER HANDLEBARS onto LOWER HANDLEBARS and align NOTCH with TAB making sure handlebars are joined together completely. Secure UPPER HANDLEBARS to LOWER HANDLEBARS using PRE-ATTACHED SET SCREWS. After handlebars are assembled they will rotate freely – be cautious. Until the WARNING machine is fully assembled, do not grab the handlebars for support. 12 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES ASSEMBLY STEP 5 HANDLEBAR COVERS UPPER HANDLEBAR NOTE: There is NO hardware bag for this step. A) Snap the front and back HANDLEBAR COVERS together onto the UPPER HANDLE BARS. Note the position of the snap tabs on the covers before snapping into position. B) Repeat on other side. BEFORE YOU BEGIN ASSEMBLY 13 IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY ASSEMBLY STEP 6 GUIDE RAIL TEFLON WASHERS (F) LOWER HANDLEBAR NUT (H) BOLT (E) ...