Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
.................... ................ .......... ............ HARDWARE BAG FOR STEP 2 CONTENTS : Elite 1.2E 2.2E Rev.1.0.indd 12-13 7/19/05 8:20:32 AM 14 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES BEFORE YOU BEGIN ASSEMBLY 15 IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY A) Open HARDWARE BAG FOR STEP 3. B) Slide the CONSOLE MAST BOOT over the bottom of the CONSOLE MAST. C) Carefully pull console wires through the CONSOLE MAST. Attach the CONSOLE WIRES to the pre-attached routing wire. Discard wire when finished. D) Slide CONSOLE MAST into MAIN FRAME. E) Insert 3 BOLTS (C), 3 LOCK WASHERS (D) and 3 ARC WASHERS (E) into back of CONSOLE MAST. F) Attach CONSOLE MAST to MAIN FRAME using BOLT (B) using NUT (F). G) Slide CONSOLE MAST BOOT down to cover exposed bolts. .................. ................ .................... .............. ................................ .............................. ........................ .................................. .......................... ................ .......... ............ .............. .......... ............ ........ .................... ............ ...... .................... ............ ................ .......... ............ HARDWARE BAG FOR STEP 3 CONTENTS : ASSEMBLY STEP 3 2.2E ASSEMBLY A) Open HARDWARE BAG FOR STEP 5. B) Remove PRE-ATTACHED BOLT & WASHERS from CONSOLE MAST. C) Slide LOWER HANDLEBARS onto CONSOLE MAST and attach by re-inserting PRE-ATTACHED BOLT & WASHERS. D) Attach UPPER HANDLEBARS to LOWER HANDLEBARS using PREATTACHED SCREWS. D) Attach HANDLEBAR COVERS using 4 SCREWS (J). ...................................... .......... .................. .............................. .................... .............................. .............. ........ ........................ .......................... A) Open HARDWARE BAG FOR STEP 4. B) Place TEFLON WASHER (H) over CRANK ARM followed by PEDAL ARM. C) Place a second TEFLON WASHER (H) over PEDAL ARM and attach using NUT (G). D) Repeat on other side. E) Attach PEDAL ARM COVERS to PEDAL ARMS using SCREWS (I). ...................................................... .................................................. .............................................. .................. ............................................................ .................................... .............. .............................. .................. .................. .............. .......... ............ .................. .......... ............ .................................. .......... ............ HARDWARE BAG FOR STEP 4 CONTENTS : ASSEMBLY STEP 4 ASSEMBLY STEP 5 .................. .......... ............ HARDWARE BAG FOR STEP 2 CONTENTS : Elite 1.2E 2.2E Rev.1.0.indd 14-15 7/19/05 8:20:38 AM 16 INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN ELLIPTICAL OPERATION LIMITED WARRANTY TROUBLESHOOTING & MAINTENANCE CONDITIONING GUIDELINES BEFORE YOU BEGIN ASSEMBLY 17 IMPORTANT INTRODUCTION PRECAUTIONS ELLIPTICAL OPERATION CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY .............................. .................... .................. .................. .............................. .................. ................ A) Open HARDWARE BAG FOR STEP 6. B) Attach FOOTPAD to FOOT PLATE using 4 BOLTS (K). C) Slide WAVY WASHER (L) and the FOOT PLATE onto the PEDAL ARM axle. D) Attach FOOTPAD BRACKET to FOOT PLATE using 3 BOLTS (M). E) Repeat on other side. ASSEMBLY STEP 6 ........ .................... ............ ................ .......... ............ .............................. ............ ................ ........ ............ HARDWARE BAG FOR STEP 6 CONTENTS : 2.2E ASSEMBLY YOU’RE FINISHED! ASSEMBLY STEP 8 ........................ ............ .............. ........................ .......................... NOTE: There is NO hardware bag for this step. All hardware is preinstalled. A) Attach the CONSOLE WIRES. B) Carefully tuck the CONSOLE MAST wires into the CONSOLE MAST before attaching the CONSOLE. C) Attach CONSOLE to the CONSOLE MAST using the 4 PRE-ATTACHED SCREWS (screws will have to be removed from the console first). DO NOT PINCH WIRES! A) Open HARDWARE BAG FOR STEP 7. B) Remove PRE-ATTACHED BOLT & WASHERS from CONSOLE MAST. C) Slide LOWER HANDLEBARS onto CONSOLE MAST and attach by re-inserting PRE-ATTACHED BOLT & WASHERS. D) Attach UPPER HANDLEBARS to LOWER HANDLEBARS using PREATTACHED SCREWS. D) Attach HANDLEBAR COVERS using 4 SCREWS (J). .............. ................ .............................. ................ .............................. .................... .................................. ASSEMBLY STEP 7 HARDWARE BAG FOR STEP 7 CONTENTS : Elite 1.2E 2.2E Rev.1.0.indd 16-17 7/19/05 8:20:41 AM INTRODUCTION BB EE FF OO RR EE YY OO UU BB EE GG II...
Ce manuel est également adapté pour les modèles :Formateurs - 1.2E (4.01 mb)