Évaluations - 5, GPA: 4
(
)
)
|
Facilité d'utilisation
Insert each carriage bolt until the square head of the bolt engages the square hole in the metal. Rotate the front base (2) and the rear base (4) so that the head of the carriage bolt is on the bottom. 2. Attach the main frame (1) to the front base (2) and the rear base (4). Position the main frame (1) onto the carriage bolts (22) which protruding through the front base (2) and the rear base (4). Secure the carriage bolts with four washers (18) and four nuts (20). Tighten the bolts securely. 3. Attach the two backrest support bars (5) and the seat support bars (12) to the main frame (1) using a stud (19), two washers (23) and two nuts (25) as shown. Be sure the eccentric axle sleeves are only side of the cushions as shown and the stud (19) is centered and then tighten the nuts (25) to where you still can rotate the support bars (5,12) freely. 4. Attach the seat adjusting lever (7) located on the main frame (1) to the two seat support bars (12) using a stud (19), two washers (23) and two nuts (25) as shown. Be sure the stud (19) is centered and then tighten the nuts (25) to where you stili can rotate the lever (7) freely. 5. Attach the seat cushion (8) to the two seat support bars (12) using four bolts (33) and four washers (31) as shown. Tighten the bolt securely. 6. Attach the backrest cushion (6) to the two backrest support bars (5) using four bolts (33) and four washers (31) as shown. Tighten the bolts securely. 7. Insert a screw down pull pin (9) into the threaded lug on the front vertical tube of main frame (1) and screw in place. Do not tighten all the way down. 8. Slide the leg frame (3) into the front vertical tube of main frame (1) as shown. Pull the handle on the screw down pull pin (9) previously installed. This will allow the leg frame (3) to slide down. Release the pin to lock in place and secure by tightening. 9. Slide the roller support tube (11) through the hole in the leg frame (3). Center the roller support tube (11) and slide a foam roller (14) onto each end of the roller support tube (11). 10. Insert a plastic roller retaining cap (17) into each end of the roller support tube (11). 11. Check all bolts and tighten as needed. „1 Nautilus® Adjustable Fitness Bench NT# 1020 \ Na util“5® AdjuS ¡tafc>íe pjtness Nautilus® Adjustable Fitness Bench NW 1020 Bolts & Bushings Size Chart ---- — --- ---- ---- --- --- --- #19 QTY:2 --- --- --- --- --- --- --- -- --- OQ 5*1 ■ i 9-3/4" (247,5mm) #22 QTY:4 #33 QTY:8 #23 QTY:6 QTY:6 QTY:1 #31 QTY:8 #18 QTY:4 #20 QTY:4 Assy# Description Qty Part# 1 Main Frame 1 Nau102001 2 Front Base 1 Nau102002 3 Leg Frame 1 Nau102003 4 . Rear Base 1 Nau102004 5 Backrest Support Bar 2 Nau102005 6 Backrest Cushion 1 Naui02006 7 Seat Adjusting Lever 1 Nau102007 8 Seat Cushion 1 Nau102008 9 Screw Down Pull Pin 1 NauRhsdpp 10 Rear Support Bar 1 Nau102009 11 Roller Support Tube 1 Nau102010 12 Seat Support Bar 2 Nau102011 13 Foot End Cap 3.55" x 1.97" 4 NauFEC90 14 Foam Roller 2 FR 100x165 15 Pivot Sleeve 0.63" Dia x 2" 1 Nau102012 16 3/8" Ball Head Nut 1 Nau102013 17 Roller Retaining Cap 2 NauUMcap 18 1/2” Flat Washer 4 washer1/2 19 Stud 5/8" x 9-3/4" 2 Stud5/8x9~3/4 20 1/2" Nylon Lock Nut 4 Locknut1/2 21 Stud 5/8" x 7" 1 Stud5/8x7 22 1/2" x 3" Carriage Bolt Cbolt 1/2x3 23 5/8" Fiat Washer 6 washer5/8 24 Bumper Cap 1.2" x 0,6" 2 BCap30x15 25 5/8" Nylon Lock Nut 6 Locknut5/8 26 3/8" Fiat Washer 1 washer3/8 27 Headwrap 1 Nau102014 28 Round Plastic Bushing 5/8" x 3/8" 22 RPB16x10 29 Foot Wheel 2 Naufootwl 30 Square Plastic Sleeve 1.9772.36" 2 SPS50/60 31 5/16" Flat Washer 8 washer5/16 32 3/8" x 3" Special Allen Bolt 1 Nau102015 33 5/16" x 2-1/4" Allen Bolt 8 Ab5/16x2~1/4 ~ 4 -- Nautilus® Adjustable Fitness Bench WT# 1020...