Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Do not use this unit with bare feet, sandals, socks or stockings! • Always examine your unit before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the unit. • Service to your unit should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys Fitness technician. Failure to follow these instructions will void the warranty. Assembly Step 1 Slide one Pillow Block Bearing (17) onto each side of the Back Rocker (5). Use two Bolts (33), four Washers (44), and two Nylon Locknuts (41) to attach each Pillow Block Bearings (17) onto the Main Frame (1). Slide Short Spacer Tube (12) into the Front Rocker (4). Attach the Front Rocker (4) to the Main Frame (1) using one Bolt (34), two Washers (44), and one Nylon Locknut (41). Insert Long Spacer Tubes (11) into the top of Front and Back Rocker (4 & 5). Attach the Connect Frame (6) to the top of the Front and Back Rocker (4 & 5). Next, insert two Bushings (29) into each side of the Connect Frame (6). Next, slide both Long Shafts (13) into Connect Frame (6) and secure in place by using four Washers (44) and four Nylon Lock-nuts (41). Figure 1 Assembly Step 2 Attach Foot Plate (7) to the Connect Frame (6) using three Bolts (32), three Washers (44), and three Nylon Lock-nuts (41). Attach Right Handle (2) and Left Handle (3) to the Main Frame (1) using two Bolts (39), four Washers (43), and two Nylon Lock-nuts (42). Figure 2 Assembly Step 3 Attach Cross Base (8) to Main Frame (1) using Plate (14), two Bolts (39), four Washers (43), and two Nylon Lock-nuts (42). Slide Pulley Block (10) onto the Cross Base (8) and secure in place using two Bolts (40), four Washers (43), and two Nylon Lock-nuts (42). Figure 3 Assembly Step 4 Attach Seat Pad (24) to Main Frame (1) using two Bolts (38) and two Washers (43). Assemble Back Pad (23) to Back Pad Support (9) using two Bolts (35) and two Washers (43). Slide Back Pad Support assembly to Main Frame (1) and secure using Pop Pin (16). Figure 4 Assembly Step 5 Start by attaching Cable (15) to Main Frame (1). See detail A below. Insert cable into Pulley V location and then attach Pulley V to Main Frame (1) using one Bolt (36), two Washers (43), and one Nylon Locknut (42). Note: Make sure cable is running through the groove of each pulley. Note: All pulleys use the same hardware to attach to Main Frame (1). Attach Pulley W to Main Frame (1) and then run cable over top of the pulley. Run cable though slot in Main Frame (1) at Pulley X location. Insert Pulley X into Main Frame (1), insure cable runs through bottom side of pulley. Run cable through Pulley Y location and then install Pulley Y onto Main Frame (1). Run cable through Pulley Z location and then install Pulley Z onto Main Frame (1). Last, thread cable end into the floating pulley of home gym unit. Figure 5 XWVYAZDetail AE TypebuttonPinBushingCable End Note: Tighten all hardware securely. Congratulations! You have completed the assembly of your new KPS-LP3. Weight Ratios 10 Parts List KF-lP3 Parts list Rev ARef #Part #descriptionQty1 3-01016MAIN FRAME, KF-LP31 19-00495HANDLE, RIGHT KF-LP313 19-00496HANDLE, LEFT KF-LP314 3-010 0ROCKER, FRONT KF-LP315 3-010 1ROCKER, BACK KF-LP316 3-01019CONNECT FRAME, KF-LP317 3-00 5 FOOTPLATE KPS-LP 18 3-01018BASE CROSS, KF-LP319 3-01017BACK PAD SUPPORT, KF-LP3110 19-00599FRAME, PULLEY KF-LP3111 10-00149LONG SPACER TUBE, KPS-LP 1 10-00150SHORT SPACER TUBE, KPS-LP 113 30-000 0SHAFT LONG KPS-LP 14 19-00005BIG PLATE, KPS-1500/1800/LP1/LP /PT115 9-0005 CABLE KPS-LP P15116 10-000 9POP PIN LOCKING117 0 -00030PILLOW BLOCK BEARING (BLACK) 18 06-00139SQUARE PLUG 50* 5619 06-00001PLUG 50.8*76. 0 06-000 0PLUG 44.51 1 06-0000 PLUG 50.8*50.81 06-0010 PLUG 3 - KPS 3 8-00 37BACK PAD, KF-LP31 4 8-00 38SEAT PAD KF-LP31 5 3-00 8BIG PULLEY 4.5"5 6 06-00061BASE PAD KPS 7 0 -00016BRONZE ID 5.46 8 0 -000 5SHORT PULLEY SPACER - KPS 9 0 -00148IRON BUSHING, KPS-LP 430 06-00039HANDLE GRIP KPS-LP1/LP 31 06-00143PEC DEC STOP BUMPER KPS- 05013 0 -00697SCREW, BUTTON HD SOCKET CAP M1 X55333 0 -00698SCREW, BUTTON HD SOCKET CAP M1 X40434 0 -00699SCREW,BUTTON HD SOCKET CAP M1 X105135 0 -00635SCREW, M10X30 BUTTON HEAD SOCKET CAP 36 0 -00664SCREW, BUTTON HEAD SOCKET CAP M10X50437 0 -00637SCREW, M10X70 BUTTON HEAD SOCKET CAP138 0 -00647BUTTON HEAD SOCKET CAP SCREW M10X75439 0 -00634SCREW, M10X80 BUTTON HEAD SOCKET CAP440 0 -00700SCREW, BUTTON HD SOCKET CAP M10X85 41 0 -0009 NYLON NUT, M1 1 4 0 -00091NYLON NUT, M101343 0 -001 8WASHER, 11* 0* 3044 0 -001 7WASHER, 13* 4*1.51745 0 -00701HEX KEY S=3146 0 -0070 HEX KEY S=6147 0 -00661ALLEN WRENCH, S=81 11 Exploded View 12 Warranty Information KEYS FITNESS PRODUCTS, L.P. LIFETIME WARRANTY This Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty is non- transferable and valid only to the original purchaser. Keys warrants that the Product yo...