Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
Before proceeding, find your new Elliptical Trainer’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, hardware or tools are missing, please call 1.800.335.4348 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw. A s s e m b l y G u i d e X1500 ELLIPTICAL TRAINER STEP 4 STEP 1 STEP 2 Stabilizer Cover STEP 1 ORANGE BAG STEP 2 • Slide a wavy washer (25x34x2T) on to the right rotation axle. Slide the knuckle joint of the pedal arm assembly onto the right rotation axle. The pedal arm roller wheel should be placed into the groove of the guide rail. Secure the pedal arm assembly to the rotation axle with a washer (8x38x2T) and bolt (M8x20L). Tighten with the 5mm Tshaped wrench. • Place the pedal arm cover over the knuckle joint. Secure in place with a washer (4x10x1T) and bolt (M4x12L). Tighten with the screwdriver. • Repeat both steps on the left side. BLUE BAG STEP3 • Slide the boot onto the console mast. • Unfold the wire harness located in the frame bracket. Wrap the end of the wire tie, located at the bottom of the console mast, around the end of the wire harness. Pull the wire tie and wire harness up through the console mast while simultaneously sliding the mast over the frame bracket. • Slide a lock washer (SW8) followed by a flat washer (8x18x1T) onto four of the bolts (M8x15L). Insert these bolts through the side of the mast to secure the mast to the frame. Slide a lock washer (SW8) followed by a arc washer (8x17x1T) onto the two remaining bolts (M8x15L). Insert these bolts through the holes in front of the mast. Tighten all bolts with the 5mm T-shaped wrench. • Slide the boot down the console mast and set it in place over the side covers. • Remove the four bolts from the back of the console. Connect the wire harness to the plug in the back of the console. Connect the heart rate wires into the heart rate plugs in the back of the console. Attach the console to the console mast with the four console bolts and screwdriver. • Attach the water bottle cage to the console mast with the two bolts located on the mast. PINK BAG STEP 4 • Slide the dual-action axle cover into place over the console mast axle. Slide a wavy washer (25x34x2T) onto the console mast axle. Slide the right dual-action arm onto the axle. Fix in place with a washer (8x38x2T) and nylon nut (M8). Cover with the included nylon nut cover. • Insert the link joint sleeve (SS41) into the socket joint of the right link arm. Position the socket joint of the link arm into the bracket at the bottom of the dual-action arm. Position the Nylon Interval Rings between the socket joint and bracket on each side. Insert a bolt (M8x45L) through the bracket, interval rings and socket joint sleeve. Secure in place with a washer (8x25x1.5T) and nylon nut (M8). Tighten with the 5mm T-shaped wrench and 13mm wrench. • Position the link arm covers over the socket joint and secure the two pieces together with a screw (M4x12L). Tighten with the screwdriver. Connect the cover to each side of the link arm with a washer (5x10x1T) and bolt (M5x12L). Tighten with the screwdriver. • Position the right footplate onto the right link arm. Secure in place with four washers (6x14x1T) and four bolts (M5x12L). Tighten with the screwdriver. • Repeat steps on the left side. • Attach the hand grips onto the dualaction arms by turning grip in a clockwise direction. Make sure it is tight. GREEN BAG STEP 3 Stabilizer Shaft Console Mast Console Boot Link Arm Covers Dual-Action Axle Cover Footplate Dual-Action Arm Hand Grips • Slide the stabilizer shaft through the plastic sleeves in the rear support tube. NOTE: A tight fit between the shaft and sleeves is important to the stability of the unit. Because of this, it may be helpful to tap the shaft through with a rubber mallet. • Slide the stabilizer covers onto the stabilizer shaft and secure with (M8x20L) bolts and (8x16x1T) flat washers. Tighten with the 5mm T-shaped wrench. • Attach end caps to the end of the guide rails with (M8x15L) bolts. Tighten with the 5mm T-shaped wrench. End Cap Pedal Arm Cover Pedal Arm Assembly Knuckle Joint Rotation Axle Hand Grips SIMPLE DELUXE PREMIER CONSOLES STEP 5 • Refer to Product Selection and Model Configuration decal on console or follow these steps. • Once the product is plugged in t...