Évaluations - 3, GPA: 4
(
)
)
|
Photos et spécifications Vision Fitness E3600HRT |
Facilité d'utilisation
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely tightening any ONE screw. 1STEP2STEP3STEP4STEP TOOLS & PARTS INCLUDED Screwdriver 15mm Pedal Wrench 5mm Allen Wrench PARTS BOX Console Mast Cover Water Bottle & Cage Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card Heart Rate Chest Strap HARDWARE INCLUDED ORANGE BAG PINK BAG M8 x 65L Screw Quantity: 2 BLUE BAG M8 x 15L Screw Quantity: 7 M8 x 20L Screw Quantity: 2 M8 x 20L Screw Quantity: 2 M8 Lock Washer Quantity: 4 M8 Lock Washer Quantity: 6 M8 Lock Washer Quantity: 2 1STEP• Install the rear foot with four lock washers (M8), two inside screws (M8x65L), and two outside screws (M8x20L). Tighten with the 5mm Allen wrench. ORANGE BAG • Install the rear foot with four lock washers (M8), two inside screws (M8x65L), and two outside screws (M8x20L). Tighten with the 5mm Allen wrench. ORANGE BAG 1STEPRear Foot 5 2STEPConsole Mast Boot Heart Rate Wires Wire Harness Console Mast Frame Bracket 2STEP• Slide the console mast boot onto the console mast. • Unfold the wire harness located in the console mast frame bracket. Connect it to the wire tie coming from the bottom of the console mast. Pull the wire tie and wire harness up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the mast to the frame using six lock washers (M8) and six screws (M8x15L). Tighten with the 5mm Allen wrench. Place the seventh screw (M8x15L) in the rear of the frame bracket and tighten until snug. • Slide the console mast boot down and snap it into place on the side cover. • Remove the nuts (M8) from the bottom of the seat. Attach the seat to the seat post with the nuts you just removed. Tighten with the 15mm wrench. BLUE BAG 2STEPConsole Mast Boot Heart Rate Wires Wire Harness Console Mast Frame Bracket 2STEP• Slide the console mast boot onto the console mast. • Unfold the wire harness located in the console mast frame bracket. Connect it to the wire tie coming from the bottom of the console mast. Pull the wire tie and wire harness up through the top of the console mast while simultaneously sliding the mast into the frame bracket. • Secure the mast to the frame using six lock washers (M8) and six screws (M8x15L). Tighten with the 5mm Allen wrench. Place the seventh screw (M8x15L) in the rear of the frame bracket and tighten until snug. • Slide the console mast boot down and snap it into place on the side cover. • Remove the nuts (M8) from the bottom of the seat. Attach the seat to the seat post with the nuts you just removed. Tighten with the 15mm wrench. BLUE BAG 6 3STEP• Feed the heart rate wires of the handlebar through the small hole located in the front of the console mast. Pull these wires up through the hole at the top of the console mast. Attach the handlebar to the console mast using two lock washers (M8) and two screws (M8x20L). Tighten with the 5mm Allen wrench. PINK BAG • Feed the heart rate wires of the handlebar through the small hole located in the front of the console mast. Pull these wires up through the hole at the top of the console mast. Attach the handlebar to the console mast using two lock washers (M8) and two screws (M8x20L). Tighten with the 5mm Allen wrench. PINK BAG 3STEPHandlebar 7 8 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2004 Vision Fitness. All Rights Reserved. 6.04 Part #Z36CB39-AG AG18.21PRD REV2 4STEPConsole Accessory Tray 4STEP• Remove the four mounting screws from the back of the console with the screwdriver. Make sure the 9-Volt bat- tery is plugged in and in place on the back of the console. Plug-in the wire harness and the two heart rate wires to the back of the console. Attach the con- sole to the console mast with the four screws removed earlier in this step. • With the screwdriver, remove the two screws located half way up the console mast. Attach the accessory tray to the console mast with the two screws. Insert the water bottle. CONSOLE 8 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2004 Vision Fitness. All Rights Reserved. 6.04 Part #Z36CB39-AG AG18.21PRD REV2 4STEPConsole Accessory Tray 4STEP• Remove the four mounting screws from the back of the console with the screwdriver. Make sure the 9-Volt bat- tery is plugged in and in place on the back of the console. Plug-in the wire harness and the two heart rate wires to the back of the console. Attach the con- sole to the console mast with the four screws removed earlier in this step. • With the screwdriver, remove the two screws loca...