Évaluations - 2, GPA: 5
(
)
)
|
Photos et spécifications Vision Fitness S70 |
Facilité d'utilisation
2009 Vision Fitness. All Rights Reserved. May be covered by one or more patents or patents pending: US 5540637, US 5573480, US 5813949, US 5813949, US 5924962, US 5938567, US 6135927, US 6149551, US 7316633, TW 364373, TW 371899, CN 99808486.7 5.09 AG18.57PRD REV3 6mm T-Shaped Wrench 8mm L-Shaped Wrench Power Cord Console Mast Console Mast Boot Accessory Tray Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card PARTS BOX 5mm L-Shaped Wrench 6mm L-Shaped Wrench S70 SUSPENSION ELLIPTICAL ™ TRAINER ASSEMBLY GUIDE End Cap Quantity:2 YELLOW BAG M8x15L Socket Head Bolt Quantity:4 M5x25L Phillips Head Bolt Quantity: 4 M5x12L Round Head Bolt Quantity:2 8.2x12.8x1.3H Safety Washer Quantity:4 BLACK BAGS x2 HARDWARE INCLUDED M8 Nylon Nut Quantity:1 M8x20L Socket Head Bolt Quantity: 4 M8 Lock Washer Quantity: 4 M8 Lock Washer Quantity: 4 M5x50L Phillips Head Bolt Quantity: 1 M8x50L Socket Head Bolt Quantity:1 GREEN BAGS x2 ORANGE BAG M8x20L Socket Head Bolt Quantity: 4 8.2x16x1.4T Washer Quantity: 4 M8x12L Flat Head Bolt Quantity: 2 M5 Hex Nut Quantity:1 HARDWARE INCLUDED To avoid possible damage to this Suspension Elliptical™ Trainer, please follow assembly steps in the correct order. Before proceeding, find your new Suspension Elliptical™ Trainer’s serial number located on the front axle tube, and enter here: Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Suspension Elliptical™ Trainer. If any parts, hardware or tools are missing, please call 1.800.335.4348 NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Suspension Elliptical ™ Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before completely tightening any ONE bolt or screw. S70 SUSPENSION ELLIPTICAL TRAINER M5x15L Phillips Head Bolt Quantity: 2 RED BAG M8 Nylon Nut Quantity: 4 M8x30L Socket Head Bolt Quantity: 4 8x13x1.4T Washer Quantity: 8 M12x95L Hex Bolt Quantity: 1 M12 Hex Nut Quantity: 1 M10x65L Socket Head Bolt Quantity: 4 BLUE BAGS x2 PINK BAG M12 Lock Washer Quantity: 1 4 ORANGE BAG 1 STEP GREEN BAGS 4 Console Mast Boot STEP NOTE: A second person will be helpful to complete this step. • Slide the console mast boot onto the console mast. • Locate the data cable and elevation motor connector in the main frame recess. Make sure they are pulled out of the opening and can be easily plugged in when the mast is inserted. • Set the console mast into the console mast frame bracket. Secure the front of the mast to the frame bracket with four socket head bolts (M8x20L), four lock washers (M8), and four flat washers (8.2x16x1.4T). Tighten with the 6mm T-shaped wrench. Secure the sides of the console mast to the console mast bracket with one flat head bolt (M8x12L) to each side. Tighten with the 5mm L-shaped wrench. • Plug in the elevation motor cable to the cable socket sitting in the frame bracket. • Wrap the wire tie that comes out of the bottom of the console mast around the data cable that exits the top of the frame. Feed the wire tie and data cable up through the channel in the side of the mast while pulling the wire tie straight up through the top of the mast. • Slide the boot down over the frame and snap in place. 1 Data Cable STEP • Connect the remote toggle cables. Place the left dual-action arm on the left rotation housing and secure in place with four bolts (M8x20L) and lock washers (M8). Tighten with the 6mm L-shaped wrench. • Line up the rotation housing cover over the rotation housing and push to snap in place. • Slide the link arm between the flanges of the dual-action arm bracket. Insert a socket head cap bolt (M8x50L) through the hole to connect the brackets. Secure with a M8 washer and nylon nut (M8). Tighten with the 10mm wrench and 5mm L-shaped wrench. • Set the dual-action cover in place over the connection bracket. Place the nut (M5) into the recess on the inside cover. Insert a bolt (M5x50L) through the outside hole and tighten to the nut with a screwdriver. • Repeat these steps on the right side with the other green hardware bag. Rotation Housing Elevation Motor Connector Elevation Motor Cable Dual-Action Arm 4 STEP 2 STEP Incline Arm Suspension Arm BLACK BAGS 5 STEP Link Arm Bracket • Position the covers over the rear incline arm bracket and secure each cover in place with four bolts (M5x25L). • Position the cover over the elevation bracket and secure with two bolts (M5x15L) from the RED BAG. • Take the rear base frame covers and pull apart to separate and slide around the bottom of the incline arm. Snap the three tabs down to set in place. • Begin pedaling to power up the unit or plug the power cord into the power socket in the front of the unit. Plug the other end of the cord into the wall outlet. Make sure the power switches at the bottom of th...