Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
Part No. Description 1 1 206647 Tank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 908076 Top Pole Section 5 1 908077 Middle Pole Section with Label 6 1 905840 Bottom Pole Section 7 1 202820 Rod, 3/8 O.D. x 4-3/4 Long 8 1 202822 Eye Bolt, 3/8 x 16 x 3-3/4 Long 9 5 202821 Disk, 2.75 O.D. 10 5 203063 Lock Nut, Nylon Insert, 3/8-16 11 1 202622 Bolt, Hex Head, 5/16-18 x 4-1/2 12 2 906411 Tank Strut, Short 13 2 906410 Tank Strut, Long 14 1 203220 Lock Nut, 5/16-18 15 1 201261 Label, Moving System 16 2 203294 U Bolt, 3/8-16 x 3.5 Long 17 8 203100 Nut, Hex Flange 5/16-18 18 1 900635 Rim 19 12* 201219 Clip, Net Holder 20 1 900416 Backboard Mounting Bracket 21 18 203309 Washer, 1 O.D. 22 4 203113 Bolt, Hex Flange, 5/16-18 x 2-1/2 Long 23 4 203798 Bolt, Hex Flange 5/16-18 x 1-1/2 24 5 201382 Support Foot 25 1 Net 26 1 207103 Pole Cap 27 4 201651 Spacer, Wheel Axle 28 1 203617 Tank Cap * YOU MAY HAVE EXTRA PARTS WITH THIS MODEL. WARRANTY CARD: Please remember to complete your product registration form either on-line at: or mail-in the enclosed postcard. 5 10/03 P/N 214782A HARDWARE IDENTIFIER Item #11 (1) Item #23 (2) Item #22 (4) Item #8 (1) Item #7 (1) Item #21 (18) Item #27 (4) Item #9 (4) Item #10 (1) 201261 3/99 1 3 2 MOVING SYSTEM 1. While holding pole, rotate basketball system forward until wheels engage with ground. 2. Move basketball system to desired location. 3. Carefully rotate basketball system upright. 4. Reattach ground restraint and check system for stability. Item #19 (12) Item #17 (8) Item #15 (1) Item #14 (1) 6 P/N 214782A 10/03 SECTION A: ASSEMBLE THE POLES 1. Correctly identify each pole section. POLE IDENTIFICATION MARK WARNING LABEL 5 4 TOP MIDDLE BOTTOM 6 2. Bounce pole top (4) and middle section (5) together as shown until they no longer move toward pole identification mark. Upright assembly. POLE IDENTIFICATION MARK 5 4 WOOD SCRAP POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 7 10/03 P/N 214782A Bounce top and middle pole assembly and bottom pole (6) together as shown until they no longer move toward pole identification mark. 4 5 6 3. WOOD SCRAP POLE IDENTIFICATION MARK POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 4 5 6 3. WOOD SCRAP POLE IDENTIFICATION MARK POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 8 P/N 214782A 10/03 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) 9/16” and 1/2” 9/16” and 1/2” OR Item #27 Item #10 Item #8 Item #7 Item #14 Item #17 Item #11 9 10/03 P/N 214782A 1. 1. Install rod (7) through holes in bottom pole (6) section and eyebolt (8). 8 7 6 2. Install wheel axle (2) through support foot (24) and install wheels (3) onto wheel axle (2) with spacers (27) as shown. 2 27 27 27 27 3 3 24 10 P/N 214782A 10/03 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Insert pole assembly into tank assembly as shown.Secure pole assembly to tank and wheel bracket as shown. Note orientation of support foot. 10 6 8 9 3. 11 10/03 P/N 214782A 4. 4. Secure tank struts to pole. Nut (14) should be tightened until flush (even) with locknuts outer edge. 11 1 14 21 21 12 13 13 12 TOP VIEW 12 P/N 214782A 10/03 13 10/03 P/N 214782A 17 9 23 21 5. Rotate non-secured ends of tank struts outward to mounting holes in tank as shown. Secure non-secured ends of tank struts to tank as shown. Repeat for opposite side. SECTION C: ASSEMBLE THE BACKBOARD This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION 1/2” 1/2” OR Item #17 Item #21 Item #22 Item #14 (1) 14 P/N 214782A 10/03 DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! 1. 17 21 22 21 18 2. Mount rim (18) to backboard and tighten completely. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! WHEN TIGHTENED PROPERLY, U-BOLTS MAY DEFORM POLE SLIGHTLY. NOTE: SAWHORSE OR SUPPORT TABLE 15 10/03 P/N 214782A 3. Install clips. CLIP “ARM” CLIP “BODY” USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS®, OR WHEN ALL SMART CLIPS® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. WARNING! 7 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrow. Push second “arm” back and into ram as shown. Twist “body” of clip slightly again to spread “arms” of clip. Clip “arms” must be flat and touching edge to edge as shown, not overlapping. A AA B BB C CC 6 16 P/N 214782A 10/03 Insert net into bottom of clip as shown. SIDE VIEW Twist net unt...