Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
BOLT............................................................................................................. 2 2. 3/8 X 3 IN. BOLT................................................................................................................. 14 3. 3/8 X 2-3/4 IN. BOLT............................................................................................................. 1 4. 3/8 X 2 IN. BOLT ................................................................................................................... 2 5. 3/8 X 1-3/4 IN. BOLT............................................................................................................. 2 6. 3/8 IN. WASHER.................................................................................................................. 25 7. 3/8 IN. LOCK WASHER...................................................................................................... 18 8. 3/8 IN. NUT .......................................................................................................................... 18 9. 3/8 IN. LOW HEIGHT LOCK NUT....................................................................................... 3 10. 5/16 IN. SNAP HOOK............................................................................................................ 4 11. STAR LOCK COLLAR.......................................................................................................... 2 12. 1-1/4 IN. SQ. RUBBER BUMPER......................................................................................... 1 13. CARRIAGE GUIDE ............................................................................................................... 8 14. 2 IN. SQ. END CAP................................................................................................................ 7 15. ROD END COVER (1/4 X 5-3/8)...................................(6249601)....................................... 2 16. 1X8 IN. GRIP........................................................................................................................ 4 17. 3/4 X 2 IN. PARAGLIDE STRIP ........................................................................................... 1 18. 1-1/2 X 2 IN. PARAGLIDE STRIP (9 PER) ......................................................................... 1 19. 1/2 IN. LG. PULLEY SPACER.............................................................................................. 6 NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: 493 BODYSMITH PROSYSTEM ASSEMBLY INSTRUCTIONS 25. To install SECONDARY CABLE (PB2559-1), start by inserting the end of the CABLE, WITHOUT the WHITE BALL under the FRONT PULLEY in the LOW ROW PULLEY HOUSING on the MAIN UPRIGHT. (REMOVE PULLEY FOR EASE OF INSTALLATION) • Push the CABLE under the FRONT PULLEY and through the HOLE of the MAIN UPRIGHT to the PULLEY on the UPRIGHT BRACE of the MAIN UPRIGHT. Pull the CABLE until the WHITE BALL stops against the FRONT PULLEY and the LOW ROW PULLEY HOUSING. • Pull the CABLE around the BRACE PULLEY and up to the SECOND PULLEY on the PULLEY BLOCK SYSTEM. (NOTE: THE CABLE MUST BE ROUTED AROUND THE SECOND PULLEY FROM THE REAR TO THE FRONT) • Pull the CABLE around the SECOND PULLEY of the PULLEY BLOCK SYSTEM and down to the first HOLE above the larger set of HOLES on the MAIN UPRIGHT. Attach the end of the CABLE to the MAIN UPRIGHT, using one (1) 3/8 X 2-3/4 IN. BOLT, one (1) 3/8 IN. WASHER, one (1) 3/8 IN. LOCK WASHER and one (1) 3/8 IN. NUT. (SEE DETAIL F) • See CABLE ROUTING DIAGRAM (DETAIL A) for help in completing STEP 24. 26. TIGHTEN ALL LOOSE PULLEY CONNECTIONS MADE TO THIS POINT. 27. Slide four (4) 1 X 8 IN. GRIPS over each end of both the LAT BAR, and the LOW ROW BAR. (NOTE: IF A LUBRICANT IS REQUIRED, RUBBING ALCOHOL THOROUGHLY COATING THE INSIDE OF THE GRIP IS THE BEST MATERIAL TO USE) (SEE DETAIL A AND B) 28. Attach the LAT BAR to the PRIMARY CABLE, and the LOW ROW BAR to the SECONDARY CABLE, by using two (2) 5/16 IN. SNAP HOOK. (SEE DETAIL A AND B) 29. To adjust the LOW ROW BAR. Remove the LOW ROW BAR from the 5/16 IN. SNAP HOOK on the SECONDARY CABLE, and attach the 24 LINK CHAIN. Attach another 5/16 IN. SNAP HOOK to the LOW ROW BAR and adjust it to the desired CHAIN LINK. (SEE DETAIL B) 30. Attach two (2) sets of UPRIGHT LABELS (designated #1 to #21) to the inside surface of both FRONT UPRIGHTS. (SEE DRAWING) 31. To use the LOW ROW FOOT BRACE, slip it over the BASE LEGS, and up against the UPRIGHTS of the FRONT UPRIGHTS. (SEE DRAWING) 7 493 BODYSMITH PROSYSTEM ASSEMBLY INSTRUCTIONS 17. Attach one (1) 3/4 X 2 IN. PARAGLIDE STRIP and one (1) 1-1/2 X 2 IN. PARAGLIDE STRIP to the ADJUSTABLE KNEE SUPPORT as shown in (DETAIL E) using the following steps: A. Thoroughly clean all surfaces where the PARAGLIDE STRIPS are to be attached. B. Remove the paper backing from the PARAGLIDE STRIPS and firmly apply the...