Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
Place all parts of the exercise cycle in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the included hex keys, assembly requires an adjustable wrench and a phillips screwdriver . PART CHART Use the drawings below to identify the small parts used in assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST on page 18. The number following the parentheses is the quantity used in assembly. Note: Some small parts may have been preassembled for shipping. If a part is not in the parts bag, check to see if it has been preassembled. M4 x 19mm Screw (73)–2 M10 x 85mm Button Screw (56)–4 M10 Nylon Locknut (48)–2 M10 Split Washer (65)–3 Black M10 Curved Washer (61)–2 M10 Curved Washer (72)–2 Black M10 x 50mm Button Screw (64)–2 M10 x 50mm Button Screw (71)–3 M4 x 16mm Screw (66)–4 M6 x 10mm Screw (60)–2 5 1. To make assembly easier, read the information on page 5 before you begin assembling the exercise cycle. Identify the Front Stabilizer (2), which has Wheels (17) attached to it. Attach the Front Stabilizer to the Frame (1) with two M10 x 85mm Button Screws (56). 2. Tighten the two Leveling Feet (29) into the bottom of the Rear Stabilizer (3). Attach the Rear Stabilizer (3) to the Frame (1) with two M10 x 85mm Button Screws (56). 3. While another person holds the Handlebar Post (6) near the Frame (1), connect the Upper Wire Harness (67) to the Lower Wire Harness (68). Next, pull the excess Upper Wire Harness out of the top of the Handlebar Post, and slide the Handlebar Post onto the Frame. Be careful not to pinch the Wire Harnesses. Attach the Handlebar Post (6) to the Frame (1) with three M10 x 50mm Button Screws (71) and three M10 Split Washers (65); tighten the two Button Screws in the front of the Handlebar Post first, and then tighten the third Button Screw. 1 56 1 17 2 2 1 29 3 56 29 3 71 65 65 1 65 71 67 68 6 6 7 4. Attach the Water Bottle Holder (18) to the Handlebar Post (6) with two M4 x 19mm Screws (73). 6. The Console (9) requires four 1.5V “D” batteries (not included); alkaline batteries are recommended. Press the tab on the battery cover and remove the battery cover. Next, insert four batteries into the Console. Make sure that the batteries are oriented as shown by the diagram inside the battery compartment. Then, reattach the battery cover to the Console. 7. Note: A long cable may be attached to the Console (9). The long cable is used during the manufacturing process. Remove and discard the long cable before continuing this step. Have a second person hold the Console (9) near the Handlebar Post (6). Connect the console wire harness to the Upper Wire Harness (67). Next, connect the game wire that has a tag to the Controller Wire (54) that has a tag. Then, connect the other game wire to the other Controller Wire. Attach the Console (9) to the Handlebar Post (6) with four M4 x 16mm Screws (66). Be careful not to pinch the wires in the Console. 4 9 6 18 73 5. Have a second person hold the Handlebar (7) near the Handlebar Post (6). Insert the Controller Wires (54) into the hole in the Handlebar Post and pull them upward out of the top of the Handlebar Post. Attach the Handlebar (7) to the Handlebar Post (6) with two Black M10 x 50mm Button Screws (64), two Black M10 Curved Washers (61), two M10 Curved Washers (72), and two M10 Nylon Locknuts (48). Be careful to avoid pinching the wires. 5 48 72 67 Hole 61 61 54 7 6 64 72 54 67 66 6 Game Wires Console Wire Harness 6 7 Battery Cover Batteries 9 8 10. Identify the Left Pedal (40), which is marked with a sticker. Using an adjustable wrench, firmly tighten the Left Pedal counterclockwise into the Left Crank Arm (15). Tighten the Right Pedal (not shown) clockwise into the Right Crank Arm. Important: Tighten both Pedals as firmly as possible. After using the exercise cycle for one week, retighten the Pedals. For best performance, keep the Pedals tightened. Press the tab on the side of the Left Pedal (40) and adjust a Pedal Strap (25) to the desired position. Adjust the other Pedal Strap (not shown) in the same way. 11. Make sure that all parts are properly tightened before you use the exercise cycle. Note: Some hardware may be left over after assembly is completed. Place a mat under the exercise cycle to protect the floor or carpet. 10 9. Attach an M6 x 10mm Screw (60) to the Seat Post (11). Next, slide the Seat Carriage (19) onto the Seat Post. Then, adjust the Seat Carriage to the desired position and tighten the Seat Knob (31) into the Seat Carriage. See the inset drawing. Attach another M6 x 10mm Screw (60) to the Seat Post (11). 8. Turn the Seat Post Knob (20) counterclockwise several turns to loosen it. Next, pull the Seat Post Knob outward, and insert the Seat Post (11) into the Frame (1). Slide the Seat Post upward or downward to the desired position, and release the Seat Post Knob. Move the Seat Post up or down slightly to ...