Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
IMPORTANT PRECAUTIONS TOOLS INCLUDEDPARTS INCLUDEDc Phillips Screwdriverc 4mm L Wrenchc 5mm L Wrenchc 5mm T Wrenchc 13/15mm Flat Wrenchc 1 Consolec 1 Console Mastc 1 Main Framec 1 Base Framec 1 Front Stabilizer Tubec 2 Pedalsc 1 Mast Bootc 1 Seat Backc 1 Seat Framec 1 Water Bottle Holderc 1 Seat Basec 1 Lower Handlebarc 1 Upper Handlebarc 5 Hardware Bagsc 1 Rear Stabilizerc 1 Seat Guide Railc 4 iPod® Adaptorsc 2 Front End Capsc 2 Rear End Capsc 2 Seat Guide Rail Capsc 2 Leveler Adjustersc 2 LevelersIf you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual. CONSOLEMAIN FRAMESEAT ADJUSTMENT LEVERFRONT STABILIZER TUBEWATER BOTTLE HOLDERUPPER HANDLEBARLOWER HANDLEBARBASE FRAME SEAT GUIDE RAIL CAP SEAT FRAME SEAT BACK REMOTE RESISTANCE TOGGLES SEAT GUIDE RAIL SEAT BASE REAR STABILIZER TUBE REAR END CAP PEDALSCONSOLE MASTMAST BOOT FRONT END CAP REAR STABILIZER TUBEREAR END CAPSLEVELERLEVELER ADJUSTERBASE FRAMEBOLT (A) SPRING WASHER (B) FLAT WASHER (C) FRONT END CAPSCREW (D) WASHER (C) BOLT (A) SPRING WASHER (B) FRONT STABILIZER TUBEMAIN FRAME ASSEMBLY STEP 1 REAR STABILIZER TUBEREAR END CAPSLEVELERLEVELER ADJUSTERBASE FRAMEBOLT (A) SPRING WASHER (B) FLAT WASHER (C) FRONT END CAPSCREW (D) WASHER (C) BOLT (A) SPRING WASHER (B) FRONT STABILIZER TUBEMAIN FRAME Open HARDWARE BAG FOR STEP 1. Slide REAR END CAPS onto REAR STABILIZER TUBE. Attach 2 LEVELERS and LEVELER ADUSTERS (found in the hardware box) to the bottom of the REAR STABILIZER TUBE and secure tightly. Attach the REAR STABILIZER TUBE to the BASE FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C). Slide FRONT END CAPS into FRONT STABILIZER TUBE with wheels facing forward and attach using 2 SCREWS (D) with provided phillips screwdriver. Attach the FRONT STABILIZER TUBE to the MAIN FRAME using 4 BOLTS (A), 4 SPRING WASHERS (B) and 4 FLAT WASHERS (C). HARDWARE BAG FOR STEP 1 CONTENTS : SCREW (D) 10 mmQty: 2SPRING WASHER (B) 15.4 mmQty: 8WASHER (C) 18 mmQty: 8BOLT (A) 20 mmQty: 8 MAIN FRAMECONNECT WIRESBASE FRAMEBOLT (A) SPRING WASHER (B) WASHER (C) ASSEMBLY STEP 2 A) Open HARDWARE BAG FOR STEP 2. B) Connect wires from BASE FRAME to MAIN FRAME. C) Slide MAIN FRAME into BASE FRAME. D) Attach the BASE FRAME to the MAIN FRAME using 5 BOLTS (A), 5 SPRING WASHERS (B) and 5 WASHERS (C). DO NOT PINCH WIRES! HARDWARE BAG FOR STEP 2 CONTENTS : SPRING WASHER (B) 15.4 mmQty: 5WASHER (C) 18 mmQty: 5BOLT (A) 20 mmQty: 5 ASSEMBLY STEP 3 RIGHT PEDALRIGHT CRANK ARMLEFT PEDALLEFT CRANK ARM Note: There is no hardware bag for this step. Attach the Right Pedal onto the Right Crank Arm, tightening it clockwise with the provided 13mm/15mm Flat Wrench. Attach the Left Pedal onto the Left Crank Arm, tightening it Counter-Clockwise with the provided 13mm/15mm Flat Wrench. Note: The Left Crank Arm is reverse threaded so it is very important that it is tightened Counter-Clockwise. Tightening it the opposite way can damage the pedal or the crank arm or both. ASSEMBLY STEP 4 RUBBER STOPPERSCREW (H) SEAT GUIDE RAIL CAPPRE-ATTACHED WASHERSPRE-ATTACHED SPRING WASHERSPRE-ATTACHED BOLTSSEAT GUIDE RAILBASE FRAMESEAT FRAMEBOLTS (F) WAVY WASHERS (G) SEAT BASESEAT GUIDE RAILSEAT FRAMESEAT LEVER CLAMPSEAT LEVERCAP RUBBER STOPPERSCREW (H) SEAT GUIDE RAIL CAPPRE-ATTACHED WASHERSPRE-ATTACHED SPRING WASHERSPRE-ATTACHED BOLTSSEAT GUIDE RAILBASE FRAMESEAT FRAMEBOLTS (F) WAVY WASHERS (G) SEAT BASESEAT GUIDE RAILSEAT FRAMESEAT LEVER CLAMPSEAT LEVERCAP STEP D STEP B RUBBER STOPPERSCREW (H) SEAT GUIDE RAIL CAPPRE-ATTACHED WASHERSPRE-ATTACHED SPRING WASHERSPRE-ATTACHED BOLTSSEAT GUIDE RAILBASE FRAMESEAT FRAMEBOLTS (F) WAVY WASHERS (G) SEAT BASESEAT GUIDE RAILSEAT FRAMESEAT LEVER CLAMPSEAT LEVERCAP NOTE: Be sure to keep SEAT LEVER positioned upward as shown. Orientate SEAT LEVER CLAMP with rounded edge facing away from SEAT GUIDE RAIL as shown above. Open HARDWARE BAG FOR STEP 4. Attach the SEAT BASE to the SEAT FRAME using 4 BOLTS (F) and 4 WAVY WASHERS (G). Remove SEAT GUIDE RAIL CAPS, then remove the PRE-ATTACHED BOLTS, SPRING WASHERS and WASHERS from both ends of the SEAT GUIDE RAIL and lift from base frame. Note the orientation of the seat guide rail. Slide the SEAT FRAME through the rear of the SEAT GUIDE RAIL as shown above. Lock SEAT FRAME into place by pusing down on SEAT LEVER. NOTE: Seat lever will face forward when in locked position. Attach the RUBBER STOPPER to the bottom of the SEAT GUIDE RAIL using 1 SCREW (H). Set assembled SEAT GUIDE RAIL on the grooves of the BASE FRAME. Re-attach the PRE-ATTACHED BOLTS, SPRING WASHERS and WASHERS through the BASE FRAME into each end of the SEAT GUIDE RAIL. DO NOT TIGHTEN UNTIL ALL FOUR BOLTS HAVE BEEN STARTED. Snap SEAT GUIDE RAIL CAPS back onto each end of SEAT GUIDE RAIL. HARDWARE BAG FOR STEP 4 CONTENTS : BOLT (F) 35 mmQty: 4WAVY WASHER (G) 18 mmQty: 4Side ViewSCREW (H) 8 mmQty: 1RUBBER STOPPERQty: 1 ASSEMBLY STEP 5 BOLTS (E) SPRING WASHERS (B) S...