Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Write the serial number in the space above for reference. Serial Number Decal (under seat) EQUIPMENT [,_i I JR :a_'gl n i_.]i _ m.. 1 HELPLINE! /-800-735-5879 ." _r_=_:lS I ROEBUCK AND CO. _a_,_)_FMAN ESTATES, IL 60179 S and instructions in this manual before using this equipment, Save this manual for future reference. new products, prizes, fitness tips, and much more! ImportantPrecautions................................................................... 3 BeforeYouBegin .................................................... 4 Part dentficat_onChart............ . ............ 5 Assembly............................................................................ 6 AdjustingtheWeightBench.............................................................. OrderingReplacementParts ...................................................... 14 BackCover Full90-DayWarranty........................................................... BackCover Note:A PartList/ExplodedDrawingisattachedin thecenterof thismanual.RemovethePartList/Exploded Drawingbeforebeginningassembly. 4... • beginning this or any exercise program, consult your physician. This iS especially e of 35or persons with pre-existing health problems. Read all • SEARS assumes no responsibility for personal injury or property damage lined by or through the use of this product, 3 man .EQr setmevercamee..e. ,ecmgIMAGE" welgl_tb_nch. The IMAGE" 3.8 is aemgned to help you develop every major muscle group of the body. Whether your goal is a shapely figure, dramatic muscle size and strength, or a healthier cardiovascular system, the'IMAGE" 3.8 will herp you achieve the specific results you want. For your benefit, read this manual carefully before using the IMAGE" 3.8 weight bench. If you have additional questions, please call our toll-free HELPLINE Right Side Weight Guide Barbell- Weight Glider Safety Backrest Seat at 1-800-736-6879, MOnday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is 831.159700. The serial number can be found on a decal attached to the IMAGE" 3.8, see the front cover of this manual). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Note: The terms "right side" and "left side" are determined relative to a person sitting on the bench. They do not refer to right and left on the drawings in this manual, Left Side Upright Storage Tube Bracket 4 • T t_\\\\\\\\\ t_\\\\\\\\\\\\\\\\_ F_ M6 x 55mm Bolt (4)--4 M6 x 38mm Bolt (60)--1 M6 x 16mm Screw M6 Washer (30)--5 M8 Nylon Locknut M8 Washer (52)--10 _\\\\\\\\\ M8 x 70mm Bolt (41)_ M8 x 65mm Carriage Bolt (59)--4 _\\\\\\\\\1 M8 x 60mm Bolt (39)--2 M8 x 30mm Bolt (38)--2 M8 x 25ram Bolt (53)--2 (3)--2 MIO Washer (6)--14 (54)--13 MIO Nylon Locknut (11)--24 MIO x 25mm Bolt (43)--2 oJ I o t'n 0,\\\\\\\\\\\\\\\\• E MIO x 65ram Carriage Bolt (40) 8 E o oO X 0 MIO x 65mm Bolt (42)4 _\\\\\\\! MIO x 70mm Bolt (46)--8 MIO x 80mm Bolt (56)--1 JJJ JJJJJJ M8 x 16mm Screw (50)--2 MIO x 115mm Bolt (55)-1 . ° 5 • r _" u Before beginning assembly, carefully read the following Information and Instructions: • Assembly requires two people. • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing matedals until assembly is completed. • Tighten all parts as you assemble them, unless instructed to do otherwise. • For help identifying small parts, use the PART 1. Before beginning, make sure that you understand the information in the box above. Note: Some parts described in the assembly steps may be pre-assembled. Press a 50mm Square Outer Cap (17) onto each end of a Base (7). Turn the Base so the large hole is in the.position shown. Insert two M8 x 65mm Carriage Bolts (59) and two M10 x 65mm Carriage Bolts (40) up into the indicated holes in the Base. Place the Base flat on the floor, Turn the Base Crossbar (20) so the waming decal is positioned as shown. Attach the Base (7) to the Base Crossbar with two M8 x 70mm Bolts (41); a Large Support Plate (12), and two M8 Nylon Locknuts (54). Do not tighten the Nylon Locknuts yet. 2. Press a 50mm Square Outer Cap (17) onto each end of the other Base (7). Turn the Base so the large hole is in the position shown. Insert two M8 x 65mm Carriage Bolts (59) and two MIO x 65mm Carriage Bolts (40) up into the indicated holes in the Base. Place the Base flat on the floor. Attach the Base (7) to the Base Crossbar (20) with two M8 x 70mm Bolts (41), a Large Support Plate (12), and two M8 Nylon Locknuts (54). Do not tighten the Nylon Locknuts yet. IDENTIFICATION CHART on page 5. • As you assemble the weight bench, make sure all parts are oriented as shown in the drawings. In addition to the included allen wren_ch , assembly requires the following tools (not included): • Two (2) adjustable wrenches • One (1) rubber mallet • One (1) standard screwdr...