Évaluations - , GPA:
(
)
)
Fabricant : Image
Taille : 3.04 mb
Nom Fichier : 70e5ef62-663e-4037-b011-f892ad0d1385.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Make sure that the Press Front Leg is turned so that the indicated hole is on the side shown. 6. Attach the Press Seat Frame (7) to the Press Upright (2) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50). Attach the Press Seat Frame (7) to the Press Front Leg (20) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 5 7 76 50 50 6 20 Hole 4 3 62 1 50 62 50 14 50 48 48 50 6 50 20 7 2 48 48 48 48 62 50 50 62 50 7 83 87 94 33 83 50 1 50 7. Insert three 1 1/2” x 2 1/2” Inner Caps (83) into the ends of the Butterfly Top Frame (33). Attach the Butterfly Top Frame (33) to the Butterfly Upright (1) with two 3/8” x 2 1/2” Bolts (87), a Support Plate (94), and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 83 92 8 89 48 48 48 89 51 6 50 48 21 Large Pin Groove 15 8. See the inset drawing. Insert two Weight Inserts (56) into each Weight (21). Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6). Slide the Weight Guides (15) through the Weight Bumpers (51) and the holes in the Press Base (6). Secure the Weight Guides to the Press Base with two 3/8” x 2 3/4” Bolts (89), four 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50). Slide the Weights (21) onto the Weight Guides (15), stacking them on top of the Weight Bumpers (51). Note: Be sure the Weights are oriented so that the large pin grooves in the Weights are on the bottom and toward the front, as shown. 9. Press the Weight Tube Bumper (18) into the Weight Tube (17). Slide the Top Weight (16) onto the Weight Guides (15), so that the Weight Tube (17) goes into the center hole in the Weights (21). 9 15 21 18 16 17 21 56 8 10 83 2 9 87 94 50 50 15 10. Press a 1 1/2” x 2 1/2” Inner Cap (83) into the end of the Press Top Frame (9). Attach the Press Top Frame (9) and a Support Plate (94) to the Press Upright (2) with two 3/8” x 2 1/2” Bolts (87) and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. Note: Be sure that the Weight Guides (15) are properly positioned in relation to the Press Top Frame (9), as shown in drawing 11 on the next page. Large Pin Groove 9 48 62 50 48 33 9 11. Secure the Press Top Frame (9) to the Butterfly Top Frame (33) with two 3/8” x 3 1/4” Bolts (62), two 3/8” Flat Washers (48), and two 3/8” Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 12. Secure the Weight Guides (15) to the Press Top Frame (9) with two 3/8” x 1 3/4” Bolts (57) and two 3/8” Nylon Locknuts (50). Tighten the Nylon Locknuts used in steps 2–12. 11 12 57 9 50 50 15 13 85 Lubricate 31 33 38 35 Axle 31 38 13. Locate and open the parts bag labeled “ARM ASSEMBLY.” Press a 1 1/2” Square Inner Cap (35) into the back of the Right Pivot Arm (85). Lubricate the axles on the Butterfly Top Frame (33). Secure the Right Pivot Arm to the right axle with two Retainer Rings (31) and a 1” Round Outer Cap (38). Do not confuse the Right Pivot Arm with the Left Pivot Arm (not shown). Note: Be sure the Retainer Rings (31) and 1” Round Outer Cap (38) are oriented as shown in the inset drawing. The Retainer Rings may break if disassembled. Repeat this step with the Left Pivot Arm (not shown) and left axle. ARM ASSEMBLY 10 14 48 48 10 84 28 10 28 48 48 53 53 14. Insert a 2” Square Inner Cap (28) into the end of a Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm (10) with two 3/8” x 1” Bolts (84) and two 3/8” Flat Washers (48). Repeat this step with the other Butterfly Arm (10). 15. Lubricate a 3/8” x 3 1/4” Bolt (62). Attach the left Butterfly Arm (10) to the Left Pivot Arm (71) with the Bolt and a 3/8” Nylon Locknut (50). Repeat this step with the right Butterfly Arm (not shown) and the Right Pivot Arm (85). 17. Insert a 2” Square Inner Cap (28) into the top of a Press Arm (77). Press two 1” Round Inner Caps (86) into the outside ends of the handles. Attach the Press Arm (77) to the Press Frame (8) with two 5/16” x 2 3/4” Bolts (96) and two 5/16” Nylon Locknuts (64). Repeat this step with the other Press Arm (77). 15 50 10 85 71 62 Lubricate 17 77 64 96 8 28 86 Handles 16. Lubricate a 1/2” x 4” Bolt (68). Attach the Press Frame (8) to the Press Base (6) with the Bolt and a 1/2” Nylon Jamnut (36). Note: Be sure the Press Frame is oriented with the indicated hole closer to the Press Upright (2). Do not over tighten the 1/2” Nylon Jamnut; the Press Frame must be able to pivot easily. 16 8 36 6 2 68 Lubricate Hole 20. Locate and open the parts bags labeled “CABLE ASSEMBLY” and “PULLEYS.” Secure a 3/8” x 2 1/4” Bolt (79) to the Right Pivot Arm (85) with a 3/8” Nylon Jamnut (63). Locate the Butterfly Cable (73), which is the shorter cable of the two that have loops on both ends. Attach the Butterfly Cable to the 3/8” x 2 1/4” Bolt (79) with a 3/8” Nylon Jamnut (63). Note: Do not fully tighten the Nylon Jamnut; the Butterfly Cable must be able to pivot easily. 11 18. Atta...