Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight bench. Important Precautions 4 Weight Storage Tube Seat Upright Weight Guide Weight Glider Barbell Safety Spotter Right Side Left Side Note: The terms “right side” and “left side” are determined relative to a person sitting on the bench. They do not refer to right and left on the drawings in this manual. Adjustment Bracket Backrest Thank you for selecting the versatile IMAGE® 3.8 weight bench. The IMAGE® 3.8 is designed to help you develop every major muscle group of the body. Whether your goal is a shapely figure, dramatic muscle size and strength, or a healthier cardiovascular system, the IMAGE® 3.8 will help you achieve the specific results you want. For your benefit, read this manual carefully before using the IMAGE® 3.8 weight bench. If you have additional questions, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is IMBE41991. The serial number can be found on a decal attached to the weight bench (see the front cover of this manual). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Before You Begin Part Identification Chart—Model No. IMBE41991 R1200A M6 x 55mm Bolt (4)—4 M6 x 38mm Bolt (60)—1 M6 x 16mm Screw (3)—2 M6 Washer (30)—5 M10 Washer (6)—14 M8 Nylon Locknut (54)—11 M8 Washer (52)—10 M10 Nylon Locknut (11)—26 M10 x 180mm 2 M8 x 80mm Bolt (9)— 1 M8 x 70mm Bolt (41)—4 M10 x 25mm Button Head Bolt (43)—2 M8 x 65mm Carriage Bolt (59)—4 M10 x 65mm Carriage Bolt (40)—8 M8 x 60mm Bolt (39)—2 M10 x 65mm Bolt (42)—4 M8 x 30mm Bolt (38)—2 M10 x 70mm Bolt (46)—8 M10 x 25mm Bolt (53)—2 M10 x 80mm Bolt (56)—1 M8 x 20mm Screw (50)—2 M10 x 115mm Bolt (55)—1 5 Assembly Before beginning assembly, carefully read the • For help identifying small parts, use the PART following information and instructions: IDENTIFICATION CHART on page 5. Note: Some small parts may be pre-assembled. Make Things Easier for Yourself! In addition to the included allen wrench , This manual is designed to ensure that the assembly requires the following tools (not weight bench can be assembled successfully included): by anyone. By setting aside plenty of time, and by deciding to make the task enjoyable, • Two (2) adjustable wrenches assembly will go smoothly. • One (1) rubber mallet • Assembly requires two people. • One (1) standard screwdriver • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing • One (1) phillips screwdriver materials until assembly is completed. • Lubricant, such as grease or petroleum jelly, • Tighten all parts as you assemble them, unless and soapy water. instructed to do otherwise. Assembly will be more convenient if you have the • As you assemble the weight bench, make sure all following tools: A socket set, a set of open-end or parts are oriented as shown in the drawings. closed-end wrenches or a set of ratchet wrenches. 1. Before beginning, make sure that you understand the information in the box above. Note: Some parts described in the assembly steps may be 1 Decal 54 17 pre-assembled. 20 Press a 50mm Square Outer Cap (17) onto each end 54 12 of a Base (7). Turn the Base so the large hole is in the position shown. Insert two M8 x 65mm Carriage Large Hole Bolts (59) and two M10 x 65mm Carriage Bolts (40) up into the indicated holes in the Base. Place the Base flat on the floor. 17 7 59 41 Turn the Base Crossbar (20) so the warning decal is positioned as shown. Attach the Base (7) to the Base 40 Crossbar with two M8 x 70mm Bolts (41), a Large Support Plate (12), and two M8 Nylon Locknuts (54). Do not tighten the Nylon Locknuts yet. 2 17 12 41 2. Press a 50mm Square Outer Cap (17) onto each end of the other Base (7). Turn the Base so the large hole is in the position shown. Insert two M8 x 65mm 54 Carriage Bolts (59) and two M10 x 65mm Carriage Bolts (40) up into the indicated holes in the Base. Large Hole Place the Base flat on the floor. 7 54 17 59 two M8 x 70mm Bolts (41), a Large Support Plate Attach the Base (7) to the Base Crossbar (20) with 20 (12), and two M8 Nylon Locknuts (54). Do not tighten the Nylon Locknuts yet. 40 6 3. Slide a Brace (2) onto the bracket on one of the Uprights (1). Attach the Brace to the Upright with two M10 x 65mm Bolts (42), four M10 Washers (6), and two M10 Nylon Locknuts (11). Do not tighten the Nylon Locknuts yet. Slide the Upright (1) and the Brace (2) onto the M10 x 65mm Carriage Bolts (40) and the M8 x 65mm Carriage Bolts (59) in the left Base (7). Attach the Upright with two M10 Nylon Locknuts (11). Attach the Brace with two M8 Washers (52) and two M8 Nylon Locknuts (54). Do not tighten the Nylon Locknuts yet. 4. Slide the remaining Brace (2) on...