Log:
Évaluations - , GPA: ( )

Instructions Image, Modèle Power Tower ST-PT Series

Fabricant : Image
Taille : 978.37 kb
Nom Fichier : 7f51b90e-0df2-4b5c-9fc0-04da068dfd7a.pdf

Langue d'enseignement: en

Le document est chargé, s'il vous plaît patienter
Le document est chargé, s'il vous plaît patienter

Facilité d'utilisation


Should any Product submitted for warranty service be found ineligible, an estimate of repair cost will be furnished and the repair will be made if requested by you upon Keys' receipt of payment or acceptable arrangements for payment. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty. PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR UNIT WITH KEYS FITNESS PRODUCTS, LP. MAIL WARRANTY CARD TO: KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355 1 Before You Start Safety Precautions and Thank you for purchasing Unit! This quality product you have chosen was designed to meet your needs for strength training exercise. Prior to assembly, remove components from the box that all the listed parts were supplied. described in the following steps and illustrations. Important Safety Information WARNING! 1) Before using this exercise unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with preexisting health problems. Keys Fitness Products LP assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 2) To reduce the risk of possible injuries to the user, it is important to review this manual and the following precautions before operation. It is the owner's responsibility exercise unit have read the warnings and safety precautions. • This strength training unit has a user 250 lbs pounds. • It should only be used on a level surface and indoor use only. It should not be placed in a garage, patio or near water. • Wear comfortable, good-quality walking or exercise shoes appropriate clothing. Do not use this exercise unit with bare feet, sandals, socks or stockings! • Always examine your strength training unit before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the exercise unit. • Service to your Keys strength training unit should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys technician. Failure to follow these instructions will void the warranty. 2 3 Assembly Accessories Assembly Accessories Angle Support (No.7) (No.21) Bolt 3/8” x 40 (2 ea) (No.29) 3/8” Locknut (14 ea) Upright Support (No.3) Support (No.15) Small Support Plate (No.25) (No.22) Bolt 3/8” x 15 (18 ea) (No.30) M8 Locknut (4 ea) Arm Pad (No.10) Support Plate (No.13) Padded Back Support (No.9) (No.23) Bolt 3/8” x 70 (14 ea) (No.31) Washer (46 ea) (No.24) Bolt M8 x 15 (2 ea) Handle Arm (No.4) Support (No.6) (No.32) Washer (14 ea) (No.26) Bolt M8 x 60 (4 ea) (No.27) Bolt M8 x 70 (4 ea) (No.33) Arc Washer (2 ea) Support (No.2) Support (No.34) Base Legs (No.5) 45 Exploded STPT Parts List Part NO. 1 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 26 27 28 29 31 32 33 34 6 Item LAT BAR UPRIGHT SUPPORT FOR LAT UPRIGHT SUPPORT FOR DIP INSIDE BEARING COLLAR DIP HANDLE ARM BASE LEGS VKR CROSS SUPPORT ANGLE SUPPORT PADDED BACK SUPPORT ARM PAD RUBBER ENDCAP FOR 55MM SQUARE FOAM PADDING 22ID X 32OD X 140 U SUPPORT PLATE RUBBER HAND GRIP (32MM ID HOLE) CENTER CROSS SUPPORT DIP HANDLE BUSHING (32MM ID HOLE) RUBBER CAP FOR LAT UPRIGHT FOAM PADDING 22 ID X 32 OD X 240 FOAM PADDING 22 ID X 32 OD X 445 END CAP25MM DIA (1”) BOLT 3/8” X 40 BOLT 3/8” X 15 HEX HEAD BOLT 3/8” X 70 BOLT M8 X 15 (9/16”) SMALL SUPPORT PLATE BOLT M8 X 60 (2-3/4) BOLT M8 X 70 (2-3/4) NON-SLIP RUBBER PAD NYLOCK NUT 3/8” LOCKNUT FOR M8 BOLT WASHER 10 X 26 X 2.0 WASHER 22MM DIA FOR M8 BOLT CURVED WASHER FOR M10 BOLT LOW CROSS SUPPORT 7 Assembly of Power TowerAssembly of Power Tower 2. Hand tighten bolts. at this time. • Connect each upright support REMOVE ALL SECURITY AND WRAPPING BEFORE BEGINNING. 1. Hand tighten bolts. Do not use wrenches at this time. • Slide rubber endcaps (11) onto each end of both base legs (5) . • Slide foam padding onto each push-up bar. • Connect low cross support (34) to each base leg with two support plates (13) . 1 8 2 9 3. Hand tighten bolts. at this time. • Connect center cross support (3) with t...

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories