Évaluations - , GPA:
(
)
)
Fabricant : Jumpking
Taille : 3.84 mb
Nom Fichier : 2096af66-2aba-4413-87c7-be65a0c8db6f.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Comtrol in more important than hight. 40. Bounce only when the surface of the bed is dry. Wind or air movement should be calm to gentle. The trampoline must not be used in gusty or serve winds. .... .... .... .... .... .... 6 Note: The the sharply spot. .... 15 1. Make sure you understand the information in the box at the top of this page before you begin assembling the trampoline. Lay three Top Tubes (1), (2) and (3) on the ground as shown. Make sure there is a T-connector(4) on Top Tube (1, A marking with bigger end), Socket(7) on the Top Tube(2, B marking with bigger end) and T-connector(4) on the Top Tube(3, c marking with bigger end). Insert Top Tube(1, A marking with small end) into Socket(7). Then insert Top Tube(1, 2) into Top Tube(3, C marking with bigger end). You have now assembled one leg section. Repeat this step to assemble three more leg sections. 1 Center 4 2, B marking 1, A marking 6 .. 7 5 12 12 3, C marking 2 .. 2. Note: This step requires two persons. During this step, you will connect the four leg sections. Hold two leg sections in the positions shown. Insert the small end of Top Tube (3, C marking) into the T-connector(4) on another Top Tube (1, A marking). Repeat this step until all four leg sections are connected. Insert a center leg(6) into the leg(5). Tighten a self-taping screw(12) into small hole in the leg(5). Insert the leg (5) into the T-connector(4). 2 2 3 3 1 1 4 4 4 5 1 3 2 4 6 3 1 2 16 .... Frame Holes V-rings 8 10 10 10 10 Springs (10) 22 Hook the V-ring .. .. .. .. .. V-ring 8 10 10 Frame Black webbing with yellow line No yellow line 3. Lay the Bed (8) on the ground inside of the assembled frame. Make sure that the two warning decals (not shown) are on top of the Bed. Note: There are V-rings around the edge of the Bed (8) and holes around the top of the frame. During this step, you will attach the Bed to the frame using the included Springs (10) for holes on top of frame and for holes on bottom of frame (see the inset drawing). Hook a spring to the Bed(8) and using the spring pulling tool(22), pull the spring from the Bed to the hole slot in the trampoline frame with even spring tension. Be careful where you place your hands, the Springs and frame joints can pinch. To attach each Spring, you will first hook one end of the Spring into a V-ring with black webbing with yelow line location (see the inset drawing). Hook the first two Spring(10) into two the V-rings (black webbing with yellow line) on the Bed(8) and into the holes on the top tube. Attach two more Springs (10) with black with yellow line location directly across the Bed (with the webbing) from the first two Spring. Attach two more Spring(10) with black webbing with yellow line location halfway between the first/second Spring(10), so eight Springs(10) are attached as shown. Attach four more Springs(10) (not shown) halfway between the first eight Springs(10). Continue attaching Springs(10) halfway between the previously attached Springs,until all the Springs are attached. During the installation of springs, wear gloves and protective eye wear. 4. Lay the Frame Pad (9) on the frame. Double D-rings on the middle of pad should be fixed exactly on the right of each T-connector of frame. Do not use the trampoline without the Frame Pad (9), which is designed to reduce the likelihood of injury to the user from coming in contact with the trampoline frame. If you do not have a Frame Pad, call our Customer Hot Line toll-free at 877-927-8777, Monday-Friday,8 a.m. -5 p.m. Central Time.(Excluding Holidays) Properly install the Frame Pad before using the trampoline. 5. Look under the trampoline and locate the pairs of straps near the edge of bed(8) and Double D-ring and webbing near the frame. See the inset drawing. A, B and C. Repeat this step with the remaining straps (not shown). Thread one end of Elastic Tie-Down, then tie a knot on V-Ring. Repeat this step with the remaining straps which at middle position of each pad section (not shown). 4 ................................Q ..........J ..........J ..........J 5 A B C Frame Pad Frame Pad Frame Pad Top tube Top tube Top tube Webbing Webbing Webbing D-ring D-ring D-ring ..............................Q Strap with Double D-ring on the pad edge Safety pad D-ring T-connector Webbing Webbing Double D-ring in the middle of pad should be fixed exactly close to the right of T connector on the top rail. 17 6. Using the included plastic tie, attach the Safety Placard (11) to the frame near the point where jumpers will climb onto and off the trampoline. The trampoline is now fully assembled. Make sure that all parts are securely attached. Familiarize yourself and all users of the trampoline with the safety precautions, use and instructional materials, and care and maintenance instructions in this manual before using the trampoline. Loosen the straps (not shown) on the underside of the frame pad (for clarity, the frame pad is not shown in the steps 8 and 11). Do not remove the frame pad...