Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help. Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment. 3 Stage 1 - Lay & Play Gym • While pressing the star buttons on a support, fit the end of the support into the large slot in one of the legs, as shown. Push the support until it “snaps” into place. • Repeat this procedure to attach the other support to the remaining leg. 1 • Slide the mode switch to for shorter play.When baby bats the toys, a single song plays with “singing” light-up stars. • Slide the mode switch to for longer play. When baby bats the toys, the music plays for about 10 minutes with “singing” light-up stars. • Locate the volume switch on the bottom of the keyboard. Adjust volume to high ; or low , for your child’s comfort. Stage Switch Mode Switch • Slide the stage switch to for use with babies lying down. Hint: If your child is not actively playing with this toy, it turns off automatically (sleep mode). • Be sure to slide the stage switch to the off position when not in use. 3 • Grasp each hanger under the keyboard and pull it down so it swings freely. • Attach the toys to the hangers as shown. • Position the keyboard so it faces you. • Fit a leg assembly to the side of the keyboard, as shown. • Turn the knob clockwise to secure the leg assembly to the keyboard. Make sure the knob is fully tightened. • Repeat this procedure to attach the other leg assembly to the keyboard. 2 Leg Assembly Knob Hanger Leg Assembly Volume Switch 4 Star Button Support Leg Large Slot Stage 2 - Sit & Play 4 • Rotate the hangers up and “snap” them into place. • Attach the toys to the hangers and tabs as shown. • While pressing the star buttons on a support, fit the end of the support into the large slot in one of the legs, as shown. The support should “snap” in place. • Repeat this procedure to attach the other support to the remaining leg. 2 1 • Position the keyboard so it faces up. • Fit a leg assembly to the side of the keyboard, as shown. • Turn the knob clockwise to secure the leg assembly to the keyboard. Make sure the knob is fully tightened. • Repeat this procedure to attach the other leg assembly to the keyboard. 3 Star Button Large Slot Support Leg Assembly Tab Hanger • Slide the mode switch to . When baby presses a key, part of a song plays with twinkling lights. With each press of a key, the song continues building, a little at a time. • Slide the mode switch to . When baby presses a key, musical scales or chords play as twinkling lights follow along. • Locate the volume switch on the bottom of the keyboard. Adjust volume to high ; or low , for your child’s comfort. Stage Switch • Slide the stage switch to for use with babies sitting up. Hint: If your child is not actively playing with this toy, it turns off automatically (sleep mode). • Be sure to slide the stage switch to the off position when not in use. Leg Assembly Knob Mode Switch Volume Switch 5 Leg To change from Stage 1 to Stage 2 • Turn the threaded knobs counter-clockwise and detach the leg assemblies from the keyboard. • Press the star buttons and remove the two supports from the legs. Now proceed to step 2. If you have not used this toy before and are assembling it for first time use in Stage 2, start with Step 2. Stage 3 - Stand & Play Piano 4 2 • Position the keyboard so it faces up. • Fit a leg assembly to the side of the keyboard, as shown. • Turn the knob clockwise to secure the leg assembly to the keyboard. Make sure the knob is fully tightened. • Repeat this procedure to attach the other leg assembly to the keyboard. 3 • Rotate the hangers up and “snap” them into place. • Attach the toys to the hangers and tabs as shown. • Slide the mode switch to . Press the keys to play note by note like a real piano, as stars light up. • Slide the mode switch to . Press the keys to hear notes that sound like they’re sung by a children’s chorus. • Locate the volume switch on the bottom of the keyboard. Adjust volume to high ; or low , for your child’s comfort. Stage Switch • Slide the stage switch to for use with standing toddlers. Hint: If your child is not actively playing wi...