Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
3. Turn Temperature Control Dial to desired temperature. Allow 2 minutes for iron to reach desired temperature. 4. To turn iron Off, turn Temperature Control Dial to O (Off) and unplug iron. To Steam Iron 1. Unplug iron. Turn Adjustable Steam Control to 0 ( Dry Iron) Set iron upright on heel rest. Open water fill cover. 2. Using a cup, slowly pour 8 ounces (250 ml) of tap water into water tank opening. Do not fill iron directly from the faucet. 3. Plug iron into outlet. 4. Turn Temperature Control Dial to desired fabric setting in the steam range. 4 5. Allow 2 minutes for the iron to reach desired temperature. 6. Set Adjustable Steam Control to the recommended steam level. See the “Fabric Setting Chart.” 7. To turn iron off, set Adjustable Steam Control to 0 (Dry Iron). Turn the Temperature Control Dial to Off. Unplug iron. 8. Empty water from the iron following directions in “Caring for Your Iron.” Water: Please use ordinary tap water. If you have extremely hard water, alternate between tap water and distilled water for use in the iron. To Vertical Steam 1. Follow Steps 1 through 5 in “To Steam Iron.” 2. Hang garment in a location that is not susceptible to damage from heat or moisture. Do not hang in front of wallpaper, window, or mirror. 3. Hold iron about 6 inches (15 cm) away from garment and press and release the Blast Button to steam out wrinkles. Do not press Blast Button more than once every 2 seconds. 4. To turn iron off, turn Temperature Control Dial to O (Off). Unplug iron. 5. Empty water from the iron following directions in “Caring for Your Iron.” NOTE: Do not allow hot soleplate to touch delicate garments. 5 840124900 Ev01.qxd 2/19/04 11:16 AM Page 6 Features Blast of Steam and Spray Buttons Push Blast Button for an extra blast of steam. Push Spray Button to release a fine spray of water for difficult wrinkles in cotton or linen. Blast Spray Light Button Adjustable Steam Control This control provides minimum steam for wool or maximum steam for linen. Set the control to 0 (Dry Iron) setting to iron without steam. Auto Shutoff Reset Button/Light This light comes on when the iron is first plugged in. After one hour, the iron will shut off and the light will go out. Push the Reset Button to turn the iron back on. Power On Light The light stays on even if Temperature Control Dial is turned to Off. 6 Caring and Cleaning Iron Storage 1. The water tank of your iron should be emptied after each use. Turn Temperature Control Dial to Off. Unplug the iron and hold over a sink. Slowly tilt pointed end down over sink. Water will run out of water tank opening. 2. After iron has completely cooled, wrap cord loosely around iron and store in an upright position. Do not store iron laying flat on soleplate. Soleplate 1. Never iron over zippers, pins, metal rivets, or snaps, as these may scratch the soleplate. 2. To clean occasional build-up on the soleplate, wipe with a sudsy cloth. Do not use abrasive cleansers or metal scouring pads. 3. Always store iron upright in the heel rest position. Self-Clean To maintain optimum steam performance of your iron: Rotate the adjustable steam control from 0 to 4 several times to remove debris and minerals from the steam valve. 7 840124900 Ev01.qxd 2/19/04 11:16 AM Page 8 Troubleshooting Troubleshooting (cont.) Iron won’t heat PROBLEM THINGS TO CHECK Water is leaking Iron won’t steam Leaves spots • Is the iron plugged in and the outlet working? Check the outlet by plugging in a lamp. • Is the Temperature Control Dial turned to a fabric setting? • If automatic shutoff model, is the Reset Button Light illuminated? If not, press to reset. • Do not overfill the water tank. • If steam ironing, is Adjustable Steam Control in a steam position, the Temperature Control Dial in the steam range, and did the iron have enough time to preheat? • If dry ironing, make sure the Adjustable Steam Control is in the DRY IRON position ( 0 ). • Check the water level. • Is the Adjustable Steam Control in a Steam position? • Has the iron had enough time to preheat? • ALWAYS empty the water tank of the iron after using. Water left in the tank may discolor clothing and soleplate. • If the iron cord should become twisted, unplug iron and let cool. Hold iron cord in the middle of entire length. Let plug and iron dangle freely until cord uncoils. This will extend the life of your iron cord. Twisted cord Fabric Nylon Acetate Wool Silk Acrylic Rayon Polyester Cotton Linen Ironing Instructions Temperature Setting Dry iron on wrong side of fabric. Steam iron with fabric still damp. Steam iron on the wrong side of fabric. Iron while still damp using steam and/or spray. 1 2 3 4 NO STEAMSTEAM PROBLEM THINGS TO CHECK Wrinkles are not removed • Check Temperature Control Dial is set to correct fabric. Iron is too hot/not hot enough • Check Temperature Control Dial and adjust to desired setting level. Let iron cool down 5 minutes before continuing. Fabric Setting Chart 89 840124900 Ev01.qxd 2/19/04 11:16 AM Page 10 ...
Ce manuel est également adapté pour les modèles :Fers - 14970 (233.42 kb)