Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
WARNING: The Auto-Off is a safety feature and is not a recommended means for turning your iron off. See “Caring for Your Iron After Use.” MOTION SMART® AUTO-OFF FEATURE (select models only) When the iron is plugged in, the Power Indicator will light steadily, indicating that there is power to the iron. IF YOU LEAVE THE IRON: • in a horizontal position without moving it, or accidentally tip the iron over, it will automatically stop heating after 30 seconds. The Power Indicator will blink to let you know that the iron has stopped heating. • in a vertical position (on its heel rest) without moving it, the iron will automatically turn off after 15 minutes. The Power Indicator will blink to let you know that the iron has stopped heating. IMPORTANT: The Power Indicator will continue to blink until the iron is unplugged or reset. TO RESET THE IRON: Move the iron back and forth and allow it to reheat for 2 minutes. The indicator will stop blinking and the iron will start heating again. WARNING: Motion Smart® Auto-Off is a safety feature, not a recommended means for turning your iron off. See “Caring for Your Iron After Use” for information on turning off your iron and storing it safely between use. STORAGE STRIP™ INDICATOR (select models only) is an easy way to see when the iron is cool enough to store. TOUSE THE STORAGE STRIP™ INDICATOR: Turn iron on. In approximately 2 minutes, the STORAGE STRIP™ INDICATOR will turn from black to red, indicating that the iron is too hot to store. When the iron is turned off, it will take the iron approximately 30-40 minutes for the STORAGE STRIP™ INDICATOR to turn from red to black, indicating that the iron is cool enough to store. CAUTION: The STORAGE STRIP™ indicator should only be used as a guideline. The iron should always be handled and stored with care. SECURECORD™ RETRACTION (select models only) allows you to safely retract your power cord without a whipping effect. 1. Select the amount of cord desired before plugging into an electrical outlet. Do not pull cord past red indicator. 2. To retract the cord use the cord prongs to press the retraction button. Hold the iron with one hand and use the other hand to grab the end of the cord. (failure to hold plug may cause plug to fly) 3. The cord reel is compact for multi-layer winding of the cord. In case cord is not fully rewound, pull out the cord and steer cord evenly on the reel. 4. In case the cord is not pulled out easily, pull cord firmly. 5. Do not allow children to use retractable cord feature as the cord may cause injury. CARING FOR YOUR IRON AFTER USE TURNING OFF YOUR IRON: Turn the Steam Lever to (Dry) and Fabric Select Dial to Off and unplug the iron from the power source. WARNING: NEVER yank the power cord when unplugging the iron. This can damage the cord. STORING YOUR IRON 1. Turn off iron following instructions above. Allow the iron to cool. 2. If you do not use your iron on a daily basis, empty the water reservoir after each use for a longer iron life. To do so, unplug the iron, turn the iron upside down, open the fill hole cover, and allow water to flow from the fill hole. Shake the iron gently to remove trapped water drops. 3. If your iron does not have a retractable cord, loosely loop the power cord around the heel rest and store the iron on its heel rest. IMPORTANT: Wrapping the cord around the iron too tightly can damage the cord. MAINTAINING YOUR STEAM MASTER® IRON CLEANING THE SOLEPLATE: turn off iron following instructions above. Clean the soleplate if starch or other residue accumulate. TO CLEAN THE SOLEPLATE: allow the iron to cool and then wipe it with a soft, damp cloth. WARNING: DO NOT use abrasive cleansers, scouring pads or vinegar to clean the soleplate. This will damage the finish. Run the iron over an all-cotton cloth to remove any residue. USING THE SELF-CLEANING FEATURE: You should use the Self-Cleaning feature once a month to maintain the optimal performance of your iron. TO USE THE SELF-CLEANING FEATURE: Turn off iron following instructions above. 1. Move the Steam Lever back and forth several times to remove debris and minerals from the Steam Valve. This keeps water flowing into the steam chamber. 2. Fill the water reservoir with tap water to the MAX line. 3. Plug in the iron, set the Fabric Select Dial to Linen and allow the iron to heat for 2 minutes. 4. Unplug the iron. 5. Hold the iron over a sink in a horizontal position. WARNING: Be careful not to touch the iron’s hot surfaces. 6. Press the Self-clean Button and hold. Water will begin dripping from the steam vents. Slowly rock the iron side to side and front to back for 30 seconds. When rocking the iron, dip the nose of the iron slightly below the rear of the iron to make certain the water circulates completely. Release the Self-clean Button after one minute. 7. Open the fill cap, turn the iron upside down, and allow the remaining water to flow out of the fill hole. 8. Dry the soleplate with a towel. 9. Plug in the iron and set the F...